Replies

  • Just want to confirm. If i use minimosd board can i connect to it my sj400 camera video out signal and trasmit both my telemetry data and my video  through the telemetry radio to my ground station.  Does the connection is as shown in reinaldo schema below?

  • I don't think you need to power both sides when wired with jumpers soldered even for uploading firmwares/chars.

  • There you go ... This setup works well for me (for my third board). Please note that I have soldered both jumpers which ties digital and analogs lines.

    3692511249?profile=original

    • I used a very similar setup to that, except my MinimOSD was grounded at the analog instead of the digital side. It shouldn't matter because the digital and analog grounds are tied using the solder tabs.

      However, my video gear was powered from the balance connector and the APM from the power module.

      If I powered the APM first and then the video gear, all worked.

      If I powered the video gear first and then the APM, then the Maxim chip fried.

      So that may happen to you too if you use that setup and power your gear up in the same way I did, even though it was from a single battery.

  • Yes! I second the request. This could be very useful.

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @gclue_akira: 柏の葉で走行させてるjetracerの中身 #instantNeRF #jetracer https://t.co/giVvuE4hP7
Jul 4
DIY Robocars via Twitter
Cool web-based self-driving simulator. Click save when the AI does the right thing https://github.com/pncsoares/self-driving-car
Jul 4
DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
DIY Robocars via Twitter
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
Jun 13
DIY Robocars via Twitter
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: My new car SPC 3.0. https://t.co/CKtkZOxeNQ
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
May 28
DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
More…