Modifying Code for Hexacopter

Hey Guys,


I am about to change the ArduCopter code (no experience there - want to try out some changes in altitude control). Now my question: For I am using a Hexacopter - do I need to specify my setup in the code? I am using Arduino to load the code to the board. In MP the setup must be specified when uploading firmware.

If I am not mistaken and this must indeed be specified in the code: Du you know were/how I can do this?

Thanks, Georg

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I have a new Problem now: I can not arm my motors anymore. It worked quite well a couple of times to upload my own code but since the last upload of my code I can not start the copter anymore. I tried the firmware via MP and the Problem is the same, then I calibrated the motors (this works). But no change...

    I will continue tomorrow - hopefully i did not break my board! Is this easy to do? :(

  • Developer
    Don't forget orientation. Look in config.h for anything you want to change by default and copy it over as a define.
  • There is the file APM_Config.h, enable the configuration of your drone

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @gclue_akira: 柏の葉で走行させてるjetracerの中身 #instantNeRF #jetracer https://t.co/giVvuE4hP7
Jul 4
DIY Robocars via Twitter
Cool web-based self-driving simulator. Click save when the AI does the right thing https://github.com/pncsoares/self-driving-car
Jul 4
DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
DIY Robocars via Twitter
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
Jun 13
DIY Robocars via Twitter
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: My new car SPC 3.0. https://t.co/CKtkZOxeNQ
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
May 28
DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
More…