You need to be a member of diydrones to add comments!
This reply was deleted.
Activity
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
Our next Virtual Race will be on June 4th:
https://www.meetup.com/DIYRobocars/events/285787423?utm_medium=referral&utm_campaign=share-btn_savedevents_share_modal&utm_source=link
RT @SmallpixelCar: Noticed my car zigzagged in last run. It turned out to be the grass stuck in the wheel and made the odometry less accura…
Replies
Is it just me or should the motor calibration gui in MP be interactive and plot the mag interference as you raise the throttle. I clicked on START, slowly raised the throttle to 50% and hold for 5 then a click down to nothing and the graph never jumps ?
When i did it the old fashioned way via the terminal i get a compassmot of about 1ish% with no props but still i expected something on the graph.
It may only be working with Arducopter 3.2. I remember trying it a couple weeks ago and it did nothing (using the page you described). I just put 3.2dev on my copter and now it works and updates live.
Just for clarification for anyone that reads your post.... a compassmot without props is not useful since it will not draw the same amount of current with props, which is what induces the compass error and determines the compensation values.
I apologise if this is a bit off topic.
My mission planner just updated to version 1.3.0.
Now, I do not have a "Terminal" icon in the upper tool bar area.
I am new to MP and the whole APM thing (getting up to speed quickly though).
Am I just not looking for the obviuos?
Thanks.....
I found exactly the same thing - Terminal has disappeared, along with other menus which used to be visible from the 'quick' section of Flight data.
I cannot see any "Advanced Menu" selection. Unless it is hidden with the Terminal selection..LOL.
Right clicking on the top tool bar just opens 2 options to select:
Auto Hide and Full Screen
Under the Config/Tuning tab, bottom right, check "advanced".
That also will bring back some of the tabs in Flight Data.
Aha, that did it. Thanks.......
What we have now is a much more comprehensive compass calibration with feedback so you can see the directions that you have pointed the vehicle. Spin the sphere around and make sure you have coverage in all quadrants.
Do you need to be outside away from buildings and metal or can you do it inside? I tried at the field but it was too tough to see the screen.