Pixhawk with DJI Lightbridge

Has anyone been able to configure a Pixhawk to work with a lightbridge HD link?

I'm able to get the Lightbridge control signals to the pixhawk but I've yet to figure out how to set the FailSafe.  When I turn off the RC controller, the lightbridge air module continues to output the same S.Bus channel signal levels. 

From talking to others I've found out that Lightbridge outputs the fail-safe "flag" in the header or footer (I'm not sure which) of the S.Bus signal (not the normal PPM channels like the pixhawk is expecting).  Can anyone confirm this is true and if so, how can I map the DJI Lightbridge failsafe signal to the Pixhawk's failsafe.

Thanks!

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Has anyone gone through LightBridge 2 link with Pixhawk?

  • Hi,

    Hi Chris, 

    I would like to know how you configured DJI Light Bridge 2 with Pixhawk Cube Autopilot. Actually i am able to receive 4 RC control channels and channel 6 but i could not find remaining channels i.e. 5, 7 and 8. Can you please help/guide in this regard.

    Thankyou

    Regards

    Yasir Khizar



    Pu Yanghuang said:

    Hi, I read the SBUS signal, and the failsafe bit is:

    I use lightbridge 2

    3702445832?profile=original

    Pixhawk with DJI Lightbridge
    Has anyone been able to configure a Pixhawk to work with a lightbridge HD link? I'm able to get the Lightbridge control signals to the pixhawk but I'…
  • Hi, Rafael Mendy,

    Did you succeed in getting more than 5 channels from LB2 for Pixhawk Cube Autopilot using Ardupilot firmware. Your help/guidance is required.

    Thankyou

    Regards

    Yasir

    Rafael Mendy said:

    Hi Andre

    Any progress in useing LB2 with pixhawk?

    are other rc channels accessible somewhere?

    ANDRE Pierre said:

    Hi,
    i got a LB2 and i've question.


    I would like to use it on a plane with a pixhawk inside.

    Actually it's working fine with the SBUS output but could you explain me why i've only 5 channels and not 14 channels like i use it on a A2 controller ?

    I've only A E T R and FLIGHT MODE (1,2,3,4,5 et 7).

    Best regards

    Pixhawk with DJI Lightbridge
    Has anyone been able to configure a Pixhawk to work with a lightbridge HD link? I'm able to get the Lightbridge control signals to the pixhawk but I'…
  • Hi Chris, 

    I would like to know how you configured DJI Light Bridge 2 with Pixhawk Cube Autopilot. Actually i am able to receive 4 RC control channels and channel 6 but i could not find remaining channels i.e. 5, 7 and 8. Can you please help/guide in this regard.

    Thankyou

    Regards

    Yasir Khizar

  • Hi, I read the SBUS signal, and the failsafe bit is:

    I use lightbridge 2

    3702445832?profile=original

  • This looks interesting but may only be for mutirotor:

    https://store.emlid.com/product/edge/

    Edge Kit with Wi-Fi
    Order Emlid Edge - Advanced drone controller with HDMI video input and 5.8 GHz data link. Full HD video streaming and telemetry up to 2 km. Featuring…
  • Hi Andre

    Any progress in useing LB2 with pixhawk?

    are other rc channels accessible somewhere?

    ANDRE Pierre said:

    Hi,
    i got a LB2 and i've question.


    I would like to use it on a plane with a pixhawk inside.

    Actually it's working fine with the SBUS output but could you explain me why i've only 5 channels and not 14 channels like i use it on a A2 controller ?

    I've only A E T R and FLIGHT MODE (1,2,3,4,5 et 7).

    Best regards

    Pixhawk with DJI Lightbridge
    Has anyone been able to configure a Pixhawk to work with a lightbridge HD link? I'm able to get the Lightbridge control signals to the pixhawk but I'…
  • Hi ! do you use the telemetry fonction with the lightbridge ?

    If yes, can you tell me how ?

    Thanks.

    CHRIS

  • solo link boards are available at $50 a pop

    https://store.3dr.com/products/solo-link-im6-board

    how to incorporate them into a pixhwark 2.1 build I've not idea though 

  • Hi,

    I got an LB2. Would like to connect it with pixhawk and have the LB2 grd control to use the gimbal. How did you exactly configured everything if you please give some detail.

    Thanks

    ANDRE Pierre said:

    Hi,
    i got a LB2 and i've question.


    I would like to use it on a plane with a pixhawk inside.

    Actually it's working fine with the SBUS output but could you explain me why i've only 5 channels and not 14 channels like i use it on a A2 controller ?

    I've only A E T R and FLIGHT MODE (1,2,3,4,5 et 7).

    Best regards

This reply was deleted.

Activity

DIY Robocars via Twitter
RT @gclue_akira: 柏の葉で走行させてるjetracerの中身 #instantNeRF #jetracer https://t.co/giVvuE4hP7
Jul 4
DIY Robocars via Twitter
Cool web-based self-driving simulator. Click save when the AI does the right thing https://github.com/pncsoares/self-driving-car
Jul 4
DIY Robocars via Twitter
RT @donkey_car: Human-scale Donkey Car! Hope this makes it to a @diyrobocars race https://www.youtube.com/watch?v=ZMaf031U8jg
Jun 25
DIY Robocars via Twitter
Jun 25
DIY Robocars via Twitter
Jun 16
DIY Robocars via Twitter
RT @GrantEMoe: I won my first @diyrobocars @donkey_car virtual race! Many thanks to @chr1sa @EllerbachMaxime @tawnkramer and everyone who m…
Jun 13
DIY Robocars via Twitter
RT @gclue_akira: JetRacerで自動走行したコースを、InstantNeRFで再構築。データセットは別々に収集 #jetracer #instantNeRT https://t.co/T8zjg3MFyO
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: SPC 3.0 Now the motor also works. This car is doable. I just need to design a deck to mount my compute and sensors. http…
Jun 13
DIY Robocars via Twitter
RT @SmallpixelCar: My new car SPC 3.0. https://t.co/CKtkZOxeNQ
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: High speed at @diyrobocars thanks @EdwardM26321707 for sharing the video https://t.co/o4317Y2U1S
Jun 7
DIY Robocars via Twitter
RT @SmallpixelCar: Today at @RAMS_RC_Club for @diyrobocars. Used @emlid RTK GPS and @adafruit @BoschGlobal IMU. Lap time 28s https://t.co/R…
May 28
DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
More…