Upload succeeded, but verify failed

Hi I am having a few issues uploading the firmware using the APM mission planner for some reason something is not working right. I am have tried various code AC 2.0.35 and APM 2.2.1And now the code that was working fine seems to be corrupted. If anyone has any quick solutions it would be great to hear them.However, what I want to raise here is that when I get an error message "Upload succeeded, but verify failed" I click OK to acknowledge the message but it does not quit and I have to close all of APM mission Planner to get rid of it.Alastair.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • I just tried to update my APM 1280 board with APM 2.2.1 HIL using the Planner 1.0.36. (I had a successful upload with Planner 1.0.34.)

     

    I too got the 'Upload succeeded but verify failed' message and Planner hung up.

    Does the CLI still work? 

  • Philip

     

    Ive just tried it on my APM 2560 board and it loaded, are you on a 1280 (that was the board I was having issues with). I am wondering if this is a memory overflow (not sure if that is the right terminology but it sounds good) Issue?

     

    I am wondering if it isn't the Planner as I loaded 2.0.35 yesterday and it worked fine on the 1280 board. Today I am changing over the RX on my quad to 2.4Ghz so I decided to update the planner and then re flash the 2.0.35 and go through the whole set-up again. that when I got the error. Perhaps there is something that the up date has changed that is specific to 1280 APM's

     

    Anyone else having issues?

     

    Alastair

  • I'm having the same problem with 2.0.35 and APM 1.0.36
This reply was deleted.

Activity

DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
DIY Robocars via Twitter
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Noticed my car zigzagged in last run. It turned out to be the grass stuck in the wheel and made the odometry less accura…
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Test my car. RTK GPS worked great. Thanks @emlid for their support. https://t.co/EkQ6qmjmWR
May 8
DIY Drones via Twitter
RT @chr1sa: @kane That's @diydrones circa 2009. Still have a box of those Canon cameras that we used to strap into planes, just like this.…
May 3
DIY Robocars via Twitter
RT @chr1sa: Our next @diyrobocars race is going to be outside at a real RC racetrack in Fremont on May 28. Fully autonomous racing, head-to…
Apr 30
DIY Robocars via Twitter
RT @f1tenth: Our Spring 2022 F1TENTH course @PennEngineers is coming to an end with a head-to-head race as a big finale. So proud of our st…
Apr 26
DIY Robocars via Twitter
RT @DanielChiaJH: I wrote a thing! Throughout the development of my @diyrobocars car I've been using @foxglovedev Studio to visualize and d…
Apr 23
DIY Robocars via Twitter
RT @SmallpixelCar: My new car for high speed. Low body, everything ( @NVIDIAEmbedded Jetson Xavier NX, @emlid RTK GPS, IMC) under the deck…
Apr 23
DIY Robocars via Twitter
Apr 21
DIY Robocars via Twitter
RT @f1tenth: F1TENTH Race training setup @PennEngineers for our upcoming ICRA2022 @ieee_ras_icra competition. @OpenRoboticsOrg @IndyAChalle…
Apr 21
DIY Robocars via Twitter
RT @fatcatFABLAB: Proud to be hosting a restarted DIY Robocars NYC Meetup April 26. Come by if you want to talk about and race self-driving…
Apr 17
More…