Hi.My final year project is working on a delivery drone that can deliver a lunch/food to offices around my small town.I have some questions that I would like to ask.1. How can I make the drone be able to locate these offices?2. How can I be sure that
Read more…I am a beginner an my goal is to 3d print a drone body and fly by FPV for photos. As this is my first build I as well am trying not to break the bank. But was wondering what experienced pilots might think between the 3DR PIXHAWK or the NAZA M. Or sh
Read more…Hello everyone!
I am planning on building a quadcopter that uses a Raspberry Pi as a flight controller. I am busy playing around with designs and the best one I have created so far has an estimated hover time of 10 minutes. I would like to increase th
Read more…Hi! I want to put myself a linear actuator on the sliding gate to the cottage. I looked in the internet, there are a lot of offers and the prices are very different. Maybe there are people here who understand this and can advise me what type of actua
Read more…i have thehttps://hobbyking.com/en_us/orangerx-openlrsng-915mhz-system-bt-tx-...i have connected like this in the videohttps://youtu.be/Pzn4jOfU_Zci have done all the steps but i cant connect mission planner via bluetooth neither droidplannerplease h
Read more…Hello,
I am trying to configure Battery failsafe on my Quad.
using mission planner software I have calibrated my battery monitor, and selected a voltage for battery failsafe, and using the reset switch given on the apm i had rebooted it, now i can veri
Read more…Hello everyone,
I have completed a parts list for a drone I am planning on building. I feel like the drone can be made more efficient and at a lower cost while providing similar capabilities. I am new to drones so if you have any recommendation, pleas
Read more…Hi all!
I want to set up pixhawk 4 on Bixler 3. For hobby purposes, FPV.
Please help with the choice between ArduPilot and PX4 and configuration.
As I understand from the forum, the ArduPilot works better with the wind.
The terrain is mountainous and qui
Introduction of axial flux stator lamination process
Disc motor has been used More and more application in recent years due to its high efficiency; while as the core component of disc motor, the axial flux stator is critical for the performance of dis
Read more…Relative newbie here looking for advice: I've done one ARF build and am now trying to move into DIY territory.
I'm setting up an APM 2.8 and I have a spare PMU from a Naza Lite system. Is there any reason I can't use the Naza PMU to power the APM? I d
Read more…Transmission lines are often located in mountainous or remote areas, making on-foot or helicopter inspections difficult, time-consuming, and dangerous. Inspections rely on manual labor that doesn’t always capture accurate data for a proper assessmen
Read more…Transmission lines are often located in mountainous or remote areas, making on-foot or helicopter inspections difficult, time-consuming, and dangerous. Inspections rely on manual labor that doesn’t always capture accurate data for a proper assessmen
Read more…Hello, all is it in the title.
i would like to do this:
http://ardupilot.org/copter/docs/common-relay.html
with that
i have 8 pwm output but no aux like P1 or P2.1, is the pix mini is capable?
i also have a pwm/relay converter in the case it's not possib
Read more…Hello all folks, Thank you for your reply in advance
And Im sorry for my bad english.
I've been flying drones for a long time as a hobby, and I'm working on the automated drone charging station project.
Charging the battery when it is plugged in to pix
Read more…Hi, i always had the question on how to manage a complete failure of Flight Control systems
i kow some implementations on extra procesors asisted systems are implemented in a great group
of modern and old flight controllers.
So for example, i think its
Read more…I am looking for an electronics Engineer that has experience designing LiPo battery charging circuity in the past. Please do not send me a cookie cutter response. I will simply reject them.
if you have a friend that has such expertise, please forward
Read more…Can anyone provide any suggestions to this issue, with an APM mini, running v3.2.1.
It's mounted on a 250 size quad. Problem is that it tries to roll left on take-off.
- APM is sited normally, arrow pointing forward. Artificial Horizon (AH) moves corre
I was working on my UAV Swarm and this thing has come up in my mind.
WHAT HAPPENS TO THE OTHER DRONES WHEN THE LEADER/MASTER DRONE LOSES ITS CONTROL AND/OR FAILS?
Does the MASTER/LEADER tag goes to the 2nd Drone or it chooses randomly or this doesn't h
Read more…For my project I need to buy airspeed and AOA sensors
as depicted in image by Sander
How to contact manufacturer or distributor ?
