Hello,
im using the turnigy plush 30A ESC's with APM2 and the ROXXY 2827/35 motor (14 pole - 760kv)
Wich settings need the turnigy plush?
Brake - no
Battery - Ni-XX (its safer?)
start mode - normal? or soft? or very soft?
timing - low? or middle? or high?
A
Read more…Hello everyone,
well hex flies stable apart from yaw will not lock i noticed in the miossion planner flight data the magnetometer is not reading correctly, in the set up i did a calibration which gave me a offset number to use, can anyone tell me whe
Read more…Hey.
I bought a set of http://store.jdrones.com/product_p/telseta01.htm
when connected to the MissionPlaner does not work...
Gents,
could anybody inform me how to change from quad to hexa after downloading 2.3 by using Arduino?? The command setup] frame hexax does not seem to work.
Sorry for asking but I am really new and 2.4 is not working for me so I need to get back to 2
Read more…Ok guys sorted the motor problem loaded the 2.4 version (thanks chris) but have a bad yaw prolem,
hexacopter swings round to the left i have to put full right stick in just to hold it, should i change the
Rate Yaw or Stabilise Yaw, increase or decrease
Read more…Hi Everyone:
I was writing a C code to read telemetry data from the arducopter. The below is my code.
It is receiving data from the arducopter, because the line "printf("%02x ", (unsigned char)temp);" does print some hex data and the data is the
Read more…Ok guys here we go, board installed radio and mavlink all works correctly, all motor power up togther
BUT pulling really bad to the right and bad left yaw, now entering cli mode doing a motor test
the front and back motors work but in the test the left
Read more…Hello all my first test flight with the ardupilot on a hex + frame was a disaster but to my problem,
when i goto cli setup motors when the front and back motor works on the pitch stick but when i try the roll stick left or right no motors work at all?
Read more…Does anybody have any good PID settings for a stock frame ArduCopter with 924kv Hacker Style motors perhaps?
Or can anybody please tell me a good way to start tuning these settings and what to look out for? All the documentation on the internet says
Read more…C'è qualcuno, meglio se principiante, per condividere e scambiare info su Arducopter?
Read more…Has anybody did such a project already?
I have plan to use CAMremote-Wifi as a ground controller for my ArduCopter.
http://arch.ced.berkeley.edu/kap/discuss/comments.php?DiscussionID=3773&page=1#Item_0
Read more…I am designing an multicopter and using ardupilot mega in it, for this apm will act as stabilising board too or with apm we should use stabilising board , i am confused...please help me
Read more…Hello.I am an avid flyer of small indoor helis but am now getting hooked on outdoor quad copters. I would love to jump in to the drone community but was wondering if the Mission program works on Apple machines.I would like to get your experiences wit
Read more…Hello. I’m a complete newbie here and I am brimming w/ questions.
First a few words about myself. I got into the RC aircraft (fixed wing & heli) many years ago. I got out of the hobby but now I have more free time than before. I recently bought
Read more…Hello all,
Anybody have an idea why jdrones store support team is not answering? (Even Jani Hirvinen)?
As I am trying to contact them since a week but there is no response.
Thx
Read more…Just placed my first order.
I'm commited now, but the DIY DRONES store said the GPS for the 3DR was on back order.
But anyway, get ready for lots of questions.
Read more…
I have finally completed my winter project - a bench top CNC mill. After several hard landings (tongue planted firmly in cheek), I want to start making my own replacement landing gear and/or electronics platform.
I am currently flying a modded version
Read more…Any suggestions which props (electric or slow flyers and size) and batteries (five or six cells) works best with the Skyjib using Axi 4120/20 motors and Phoenix Ice 75 speedcontrollers?
Read more…Can anyone help me there? I want to do a test flight tomorrow but I need to understand what's going on first.
http://diydrones.com/forum/topics/test-flight-with-2-2b6-some-issues
Read more…