Gender
Male
About
Location
Tempe, AZ
About Me:
I am currently MS Mechanical Engineering student at Arizona State University. I am building & flying Aeromodels from last 5 years. I have Worked on Micro Aerial Vehicles (200 mm wing span) Currently I am working on High lift Aircraft for SAE Aero West competition & SEDS-USA High Powered Rocket challenge.
Please tell us a bit about your UAV interest
I am very fascinated to build UAV with particular mission purposes & with introduction of open source technology, I want to develop low cost UAV's.
Hometown:
Mumbai
Activity Feed
"Hi All,
I am having the same issues that I am not able to operate my Tarot 2-D gimbal through RC.
Here are more details about my systems and things I've tried so far.
1. Pixhawk with Arducopter V3.3.3,
2. S900 airframe
3. Followed all the…"
I am having the same issues that I am not able to operate my Tarot 2-D gimbal through RC.
Here are more details about my systems and things I've tried so far.
1. Pixhawk with Arducopter V3.3.3,
2. S900 airframe
3. Followed all the…"
"Does anyone know off any documentation of adding external IMU specifically MPU 6000 to Pixhawk?"
"Hi Nizobe,
Sorry It skipped out of mind to reply earlier.
Are you trying to setup the the SITL or something else ?"
Sorry It skipped out of mind to reply earlier.
Are you trying to setup the the SITL or something else ?"
"Yes, it's true that Windows Surface with Windows 8 RT doesn't support Mission Planner or any other GCS."
"Hi Nizobe,
I couldn't solve that but I stopped using that tutorial. Instead I started using the newer tutorial released by them ( http://dev.ardupilot.com/wiki/setting-up-sitl-on-windows/#Setting_u... ). I was able to perform the simulations…"
I couldn't solve that but I stopped using that tutorial. Instead I started using the newer tutorial released by them ( http://dev.ardupilot.com/wiki/setting-up-sitl-on-windows/#Setting_u... ). I was able to perform the simulations…"
"Is This a relative wind with respect to APM or is it true wind prediction ?"
"Hi Justin
Are you still working on SITL, I wanted to simulate different wind conditions ?"
Are you still working on SITL, I wanted to simulate different wind conditions ?"
"Thanks Rasmus,
I am still working on running some simulations with study wind effects.
I got to enter my custom way-points and add winds but still working on connecting it to FlightGear or XPLane. "
I am still working on running some simulations with study wind effects.
I got to enter my custom way-points and add winds but still working on connecting it to FlightGear or XPLane. "
"I faced lot of errors while setting up and I got it working once (and Thank god I saved it to a harddrive with working SITL setup, which I couldn't setup on again due to JSBSim path error, anyway it's working now) with this tutorial…"
"Thanks Rasmus for your reply. Any other discussion you remembered, where SITL is in active discussion now ? I was working towards my Masters research and your thread helped me a lot in getting SITL started but I was hoping to get some more help from…"
"Hi Rasmus,
Thanks for your Tutorial, Are you still supporting SITL ? I am referring to this tutorial SITL ArduPlane and having some issues with connecting it to X-Plane."
Thanks for your Tutorial, Are you still supporting SITL ? I am referring to this tutorial SITL ArduPlane and having some issues with connecting it to X-Plane."
"Yes, I did. I pressed the safety switch and then I tried to arm by moving Throttle stick to bottom right but the red light on safety switch didn't go solid.
This also depends on the firmaware as well, right ? because when I used Arduplane…"
This also depends on the firmaware as well, right ? because when I used Arduplane…"
"Did it work ?
I am also trying to load arduplane firmware on Pixhawk, it did upload the firmware but doesn't operate the servos even though my Spectrum DX7z is bound via DSMx"
I am also trying to load arduplane firmware on Pixhawk, it did upload the firmware but doesn't operate the servos even though my Spectrum DX7z is bound via DSMx"
"How do I arm the pixhawk for with arduplane firmware ?
I am using Pixhawk for Skyhunter 1800 mm plane. I have installed latest Arduplane 2.78b firmware. I am using Spectrum DX7s transmitter and connected to Pixhawk via DSMx. I could see all stick…"
I am using Pixhawk for Skyhunter 1800 mm plane. I have installed latest Arduplane 2.78b firmware. I am using Spectrum DX7s transmitter and connected to Pixhawk via DSMx. I could see all stick…"
"Hi
Does APM Planner 2.0 supports Simulation (HILS and SITL) ?"
Does APM Planner 2.0 supports Simulation (HILS and SITL) ?"
Hi all, Is it not good idea anymore to run SITL on windows 7 platform (with cygwin interface plus pyserial and other add ons) ? As I see dev.arupilot.com has removed the previous SITL tutorial, which was showing instruction to run the SITL on…
