Gender
Male
About
Location
Type a choice below ...
About Me:
I live in Far North Queensland Australia
Please tell us a bit about your UAV interest
I'm fairly new to this and want my multirotor for fpv and aerial video whilest traveling around .
Hometown:
Karumba
Activity Feed
"Yes I realise that voltage under load is lower, but I don't have logs to show voltage at the time off the issue. I wanted to be able to give you all a indication of voltage and a stable resting voltage was all I had.
I don't believe my esc's have a…"
I don't believe my esc's have a…"
"Its a bit of a drama if you fly over scrub when it decides to land... Next time I get to fly I might try flicking to a different flight mode when it trys to land, to see if I can abort landing?"
"I think you are on to something with the low voltage side of things, as I normally don't draw my battveries down this far and this is the first occurance of this 'autoland' that I have had. Seems funny that the time I run my batteries a bit harder I…"
APM 2.5 Quad on firmware 2.9.1.b throttles down and lands by itself even while applying more throttle in stab mod? It throttles back and lands as if the apm is telling it to like in rtl mode but from what ever altitude you currently are at and…
"Yeah sorry mate about the battery thing.
Yeah I am not flying over a body of water, maybe some very sholw swamps. There are some great 'water proof' frames getting about now. I like the quadh20 , frame isnt cheap but well thought out.
My partner…"
Yeah I am not flying over a body of water, maybe some very sholw swamps. There are some great 'water proof' frames getting about now. I like the quadh20 , frame isnt cheap but well thought out.
My partner…"
"@ Soviet87 mmm copy-pasta yum :-)
On a serious note, I hope HK gets a good slap on the knuckles for smashing the window and running off with the name in broad daylight !
I guess you know your product is good when a major company wants to steal it…"
On a serious note, I hope HK gets a good slap on the knuckles for smashing the window and running off with the name in broad daylight !
I guess you know your product is good when a major company wants to steal it…"
"Sorry my post was too long so I had to cut it into sections. Also I found this Calculator which you might find useful if you haven't already found it yourself. "
"I got an email yesterday saying my FPV gear has been shipped, it has been held up for a month because I ordered some servos for a gimbal that were on backorder. Its coming from the UK so I guess it will be a couple of weeks
. A mate of mine and his…"
. A mate of mine and his…"
"Wow you went to 100m , 328ft that would be scary hardly being able to see your orientation. Especially here as you always need to have a bit of stick input to counteract the wind, I would have a finger resting on the rtl switch lol.
After my bit of…"
After my bit of…"
"Sounds like you well and truly have a head start on me with the gps waypiont mission side of things!
Firstly you draw your lipos down to 30% !? What is the settled voltage at 30%? I don't think you should/ are meant to draw lipos down past 80% if…"
Firstly you draw your lipos down to 30% !? What is the settled voltage at 30%? I don't think you should/ are meant to draw lipos down past 80% if…"
"I am using a HK H.A.L. quad frame with APM 2.5, 433mhz 3dr radios, HK 30 amp blue esc flashed with simonk firmware, 35 NTM motors and currently 1147 props. I have been working through testing different flight modes and rtl at different locations.…"
"Ok so I think I have it... ?
So, the 3DR radio will be the dominant component so it is connected as normal. In order (as printed on board top to bottom) GND, CTS, 5V (redwire),RX,TX and RTS has nothing but a blank pin hole on the plug.
So if I am…"
So, the 3DR radio will be the dominant component so it is connected as normal. In order (as printed on board top to bottom) GND, CTS, 5V (redwire),RX,TX and RTS has nothing but a blank pin hole on the plug.
So if I am…"
"I am interested on how people do this too, as I have found no documentation of it anywhere. I am using 433Mhz 3dr radios not that it should be any different."
