About

Gender

Male


Please tell us a bit about your UAV interest

Hobby


Hometown:

Islamabad


Activity Feed

Arif Saleem replied to Arif Saleem's discussion Help!! uBEC wire almost burnt powering APM2.5 on Skywalker Maiden in ArduPlane User Group
"Hi Ben
Point taken!!
Let me recheck everything again.

thanks"
Nov 21, 2014
Arif Saleem replied to Arif Saleem's discussion Help!! uBEC wire almost burnt powering APM2.5 on Skywalker Maiden in ArduPlane User Group
"Thanks faraz and Rehan
If this is the case then a thin wire of balance charger would have not survived for 7 minutes as i had pulled 30 amp and on average 15 amps.
Would try to figure out. 
i appreciate your help.

arif"
Nov 15, 2014
Arif Saleem replied to Arif Saleem's discussion Help!! uBEC wire almost burnt powering APM2.5 on Skywalker Maiden in ArduPlane User Group
"Hi Keith

Thanks
But this is the input ubec powering the APM,(with JP1 removed)  its not at the output powering servos.
Any thoughts??
regards"
Nov 14, 2014
Arif Saleem replied to Arif Saleem's discussion Help!! uBEC wire almost burnt powering APM2.5 on Skywalker Maiden in ArduPlane User Group
"AoA
Dear Ahmed Rehan. thanks for quick reply.
From which country you are? if you are from Pakistan , i can call you to undersatnd better.
I have my speed controller on output side. ubec is on input side of APM powering APM and xbee module. the…"
Nov 14, 2014
Arif Saleem replied to Avalerion's discussion Max power through telemetry port on APM
"Hi
I am facing a some what similar problem. I have same xbee. powered from input rail. my ubec connected to input got hot and  almost all its black ground wire burnt. is it that xbee is draining power.??

thanks
arif "
Nov 14, 2014
Arif Saleem posted a discussion in ArduPlane User Group
Hi AllI need help. I had maiden flight my skywalker 1680 with APM 2.5. There was no FPV gear and powered by 3s 5000mah battery. I am using a separate 3 Amp uBEC (max 5 amp) to power the APM to the input rail. so JP1 jumper was off. The ubec was…
Nov 14, 2014
Arif Saleem replied to Arif Saleem's discussion Which stable APM firmware for APM 2.5 hardware on Skywalker 1680 in ArduPlane User Group
"Hi Fred
Hope you are well.
can you please tell me where did u place CoG?? i am a beginner so is extra cautious. some say servo line some 30mm behind it. all confusing.
i have older skywalker v5 1680.
how much should be control throws?
would…"
Nov 3, 2014
Arif Saleem replied to Arif Saleem's discussion Which stable APM firmware for APM 2.5 hardware on Skywalker 1680 in ArduPlane User Group
"Hi
Thanks Fred for useful info.
Cala can you please elaborate your post. I did not get it.

thanks"
Sep 22, 2014
Arif Saleem replied to Arif Saleem's discussion Which stable APM firmware for APM 2.5 hardware on Skywalker 1680 in ArduPlane User Group
"Hi Fred 
thanks for help. I understand that 4s has more power. Perhaps my higher KV motor may compensate for lower voltage 3s battery. That combination was recommended by builders for 3s. lets see.
I also have APM installed exactly as yours .
Have…"
Sep 21, 2014
Arif Saleem replied to Arif Saleem's discussion Which stable APM firmware for APM 2.5 hardware on Skywalker 1680 in ArduPlane User Group
"Hi Fred
What do u recommend for first flights. Manual mode. Then stabilise and so on ?? Did u auto tune ??
Have u any links for Ur build blogs or flight blogs. I just need tips for this sky walker APM build. Thanks"
Sep 21, 2014
Arif Saleem replied to Arif Saleem's discussion Which stable APM firmware for APM 2.5 hardware on Skywalker 1680 in ArduPlane User Group
"Hi Fred
thanks a lot, i hope u would be a great help.
i have seen my default values, these are way different in many parameters. i have 3.03. Have u loaded skywalker parameters from some configuration files??
can u please also send me some pics of…"
Sep 21, 2014
Arif Saleem posted a discussion in ArduPlane User Group
Hii am new to APM and have assembled skywalker 1680 for FPV. I have APM 2.5 Board.Now the plane release is at 3.1.1. However most changes are for Pix Hawk Board.I just need a safe stable and mature release on APM. Dont need any advanced features.…
Sep 21, 2014