Gender
Male
About
Location
Lillesand
About Me:
Addicted to be Airborne
Please tell us a bit about your UAV interest
Engrossed by technology and allways like to push the limits.
Hometown:
Lillesand
Activity Feed
"Looking forward to the 100k suprise... :) Well done."
"If anyone wants to fly LTE, then check out my latest build, UAVcast-ProYou are ready in 15min, no linux skills required.https://uavmatrix.com/uavcast-pro/ Cheers//Bernt Christian Egeland"
"Inadyn is DDNS client :)"
"Great contribution Bill.
I dont know the pre-installed software for ubuntu, but i post my "top of mind" anyway.System Software
- Inadyn
- dnsutils
- modeswitch
- proftpd
- VLC (Some people prefer VLC over gStreamer)
- Uqmi…"
I dont know the pre-installed software for ubuntu, but i post my "top of mind" anyway.System Software
- Inadyn
- dnsutils
- modeswitch
- proftpd
- VLC (Some people prefer VLC over gStreamer)
- Uqmi…"
"Congrats guys. keep up the good work.
I will definitely buy Navio2"
I will definitely buy Navio2"
"Hi Ted.
Great achievement.
Could you provide more info on your setup.Which modem are you using? Do you connect using true LTE? Software used? Camera?Anyway, looking forward to see some flight vid..."
Great achievement.
Could you provide more info on your setup.Which modem are you using? Do you connect using true LTE? Software used? Camera?Anyway, looking forward to see some flight vid..."
"Had a great flight yesterday, worth sharing.
Happy flying everyone..."
Happy flying everyone..."
"@Sterling
RPI & APM need to share the same ground to communicate via serial. Just connect any ground cable from APM to any ground pin at RPI. IMPORTANT.! Don’t connect + cable between them ONLY ground cable.
For the ser2net config, you should…"
RPI & APM need to share the same ground to communicate via serial. Just connect any ground cable from APM to any ground pin at RPI. IMPORTANT.! Don’t connect + cable between them ONLY ground cable.
For the ser2net config, you should…"
"Hi Sterling.
You dont need level converter when connecting APM tx/rx -> RPI GPIO. I never used it and it works everytime despite the serial voltage diffrence.
The drawback is ser2net is only supporting TCP.
Did you install the ser2net properly?…"
You dont need level converter when connecting APM tx/rx -> RPI GPIO. I never used it and it works everytime despite the serial voltage diffrence.
The drawback is ser2net is only supporting TCP.
Did you install the ser2net properly?…"
"Well done Silvio.
I’m looking forward to see flight videos introducing 4gmetry."
I’m looking forward to see flight videos introducing 4gmetry."
"I made an ARTICLE which explains my configuration. Happy Flying. :)"
"@Jouni HelminenSkua is a great airplane and yes you can hand-launch it without any problem. What do you get for 60$ nowadays, :) Just PM me or mail me at uavmatrix@uavmatrix.com"
"@benbojangles
Left stick is always centered, I need to force it back or forth to adjust the throttle. But while in air i normally i use cruise mode and left stick is not used. One idea is to remove the X-axis spring inside the controller. Not…"
Left stick is always centered, I need to force it back or forth to adjust the throttle. But while in air i normally i use cruise mode and left stick is not used. One idea is to remove the X-axis spring inside the controller. Not…"
"@Marc Dornan I’m not sure how much data i consumed. I will check next time and post the numbers. @johnkowalsky This setup makes it allot easier and cleaner. One piece for everything. :) Before when I’m used Pixhawk or APM, i had to use TTL to UDP…"
"@benbojanglesYes its possible to increase the video performance. For some reason the gstreamer did`t work as intended with Real Time Kernel for RPI. I will look into that.Im only using the embeded Joystick function in Mission Planner. No need for…"
"@Justice Bentz Yes correct. As long as you have power and cellular network you can fly unlimited.
It will switch between 3g and 4g seamlessly. "
It will switch between 3g and 4g seamlessly. "
