Are there any plans to add support for a bicopter configuration such as (Avitar type).
Apparently you can use a KK board to fly one manually,But it would be great if the code could support the configuration so we can fly auto missions etc.
Read more…I am wanting to install the Hil firmware on to a pixhawk to do some simulations in xplane but keep getting upload errors.Works fine on APM.
Is this possible to do with a pixhawk?
Read more…I can not get newer firmwares then 2.7 in hil mode to work with xplane. I can run a simulation fine using older firmware but not with newer firmware as i want to test out geofencing that is not in the older firmware.
With the newer firmware there is n
Read more…I am wondering how multiple fail safes can be set up such as in this situation.
If i am flying in Auto mode and the plane flys out of range of my rc transmitter the plane continues in auto mode. I have been able to achieve this just by setting the fai
Read more…Just wondering if anyone can help me out my 3dr apm is very slow to respond to changes in pitch as can be seen in this video https://www.youtube.com/watch?v=HusPjTvl970
, roll and yaw are fine and respond instantly but there is a massive delay with
Read more…I have just upgraded firmware to V3.0.3 but there is no option in the flight modes for auto tune.
how do I get the auto tune flight mode?
Read more…I have seen config files for a boomerang and a tiger nitro planes but am unable to find them again as they are not listed here http://plane.ardupilot.com/wiki/configuration-files-for-common-airframes-2/
Could someone lead me to the right place as I th
Read more…I just updated the firmware on my amp 2.5 and now in stabilize mode if i bank the plane right the elevator goes up and if i bank it left the elevator goes down ,the elevator should not even be moving the ailerons should be.
everything is connected cor
Read more…I have just finished building an antenna tracker and am trying to get it to work with mission planner,
I have the servo's and movement setup in Maestro but mission planner will not connect to the servo board I keep getting this error.Have all the driv
Read more…Is it possible to have two ground stn radios and one radio in the uav,
I want to have a radio on the ground connected to a laptop running mission planner and the other connected to a tablet running droid planner.
The tablet would be used for monitoring
Read more…Looking up Antenna Tracking in the arduplane wiki and it describes Automatic camera tracking instead of how to setup antenna tracking? I think it has the wrong heading
Where can i find info on setting up Antenna tracking and not camera tracking.thanks
Read more…My first flight today with a amp 2.5 installed in a fpv phantom wing the flight was great in manual .
Though I do have a few issues first is this message no rc receiver in mission planner yet everything is connected up?.
Read more…After installing the new 2.9 firmware the hud in the mission planer is tilted to the left by about 10 degrees.
I have done the calibration followed the video and steps tilting the quad in all directions as directed but the hud is still tilted to the o
Read more…Is there a way to create a GPX file from and image that has gps data in its Exif
I am trying to use Palentier to overlay images onto Google earth but it requires you to load the jpg image and gpx track data in order to match it up and then export as a
Read more…Mission planner will no longer connect to my rfd 900 radio modems set on com port 4 at 57600.
In the config utility I click load settings and it communicates with the modems and the settings come up,but if i go to the flight data page and click connec
Read more…I have been practicing auto landings on the computer using xplane 10 and am wondering if there is a way to make the plane flair before touch down as the landings are to hard and the plane slams into the ground. So is there a way to program in mission
Read more…Just wondering if it is possible to upload a mission plan while the plane is in the air.
I know you can click on the screen and click fly to here while plane is in air but wondering if
One person takes off and flies the plane manually and another write
Read more…