Gender
Male
About
Location
No State
About Me:
Born in '79, loves to fish
Please tell us a bit about your UAV interest
To know where the fish stands, it would be a huge help to know the layout of the lake. What better way than a gps enabled boat for that job?
Hometown:
OSLO
Activity Feed
"WoW. That's a nice build. No Major Problems? What about minor?"
Hi,Got a message the my two T100 was on the way, so I was wondering if someone had used them for a build yet. Didn't find a thread about it, but someone must have got them and hopefully used them? What kind of hull have you build (or planed?)Carl
"TCIII: Yes I pledged for two thrusters and esc."
"2 thruster, 2 esc and 1 shipping outside US. "
"Hi,
I have reversed the right joystick, forward/backward motion, so the bar are changing like described. However, when I'm trying to change the rcmap of pitch and throttle the left motor runs continuously and only slows down, but don't stop, when…"
I have reversed the right joystick, forward/backward motion, so the bar are changing like described. However, when I'm trying to change the rcmap of pitch and throttle the left motor runs continuously and only slows down, but don't stop, when…"
"Channel assignment:
I use channel 1, 2 5 and 6 on the futuba receiver.
Channel 1 is connected to apm input #1, channel 2 is connected to apm input #3On the output side output 1 is connected to the left motor, and output 3 to the right motor. …"
I use channel 1, 2 5 and 6 on the futuba receiver.
Channel 1 is connected to apm input #1, channel 2 is connected to apm input #3On the output side output 1 is connected to the left motor, and output 3 to the right motor. …"
"Hi,
I have removed all electronics from the boat, and taken it in. But I'm unsure how to troubleshoot futher. I'll try to use input two again. Any tip for how to find the mapping for the receiver would also be greatly appreciatedRegardsCarl"
I have removed all electronics from the boat, and taken it in. But I'm unsure how to troubleshoot futher. I'll try to use input two again. Any tip for how to find the mapping for the receiver would also be greatly appreciatedRegardsCarl"
"I tried to move the cable from rc receiver output channel 2 from apm input nr 3 to input nr 2, and apm output nr 3 to outpput nr 2 but after that I didn't have any output too right motor.
Log files are ziped, and can be found here. All the log files…"
Log files are ziped, and can be found here. All the log files…"
"I have bought a pair of pontoons a few months back for the same purpose. This was the once I bought, quite thin these also, but I guess every ounce counts on a rc plane. China Post have post rates that are quite low compared to usps, when you live…"
"I'll try steering mode later today, I don't need the learning mode, so I can swap that.
Brushed motors change the directions if you swap the cables.
The two main issues right now seems to be:
1: the motors goes quite well in reverse, but only small…"
Brushed motors change the directions if you swap the cables.
The two main issues right now seems to be:
1: the motors goes quite well in reverse, but only small…"
"Power Module (PM) with it's own battery. And that works okey for the APM.
I need to check the voltage when I get home (I'm at the cabin now, and have forgoten to take a voltmeter with me.)But going forward is still burst, going reverse is okey. …"
I need to check the voltage when I get home (I'm at the cabin now, and have forgoten to take a voltmeter with me.)But going forward is still burst, going reverse is okey. …"
"ok, new update, after looking into this problem, i connected the pc directly to the apm via usb, and it worked alot better. it's steady in reverse. and forward is a lot more "correct bursts" disconnected the pc, and the telemetry (and broke the…"
"I also noticed something today, which can be (part of) the trouble:Everytime i start running the motors, I get bad gps health and disarmed. As stated before, I'm quite new to this, but I guess the engines could make some noise on the electrical…"
"HI Thomas,Thanks again for using your time to help me :)
If I understood the joystick layout right, I'm using the elevator joystick for throttle, (that's the right joystick right?) and the Aileron joystick for steering (same joystick, just the other…"
If I understood the joystick layout right, I'm using the elevator joystick for throttle, (that's the right joystick right?) and the Aileron joystick for steering (same joystick, just the other…"
Hi all,TCIII asked me to post this here, so more brains could tell me where I'm being newbee or stupid. Just don't RTM me please, as there is a lot of stuff to cover for a new head here, and alot of doesn't count for a boat or rover. :)Okey, back in…
"Great :) I will update my blog with the latest udates soon. I just have a few issues wich TCIII have stared helping me with on ardupilot forum. Carl"
