About

Gender

Male


Location

Longview, WA


About Me:

2 years flying Gaui 550 and now flying a APM quad for several months.


Please tell us a bit about your UAV interest

I am interested in FPV with a quadcopter and of course all the other fun stuff like auto missions with mission planner and RTL etc.


Hometown:

Longview, Washington


Activity Feed

Charosenz replied to Charosenz's discussion manually tilt camera platform with Tx pot - need advise with wiring
"disregard.   Honestly, I am surprised after about 2 weeks no one offered any help.   I got help really fast on RCG.  I don't mean to offend anyone, just stating the results
The answer is "no".    You have to have a controller to operate a gimbal…"
May 4, 2014
Charosenz posted a discussion
I want to simply tilt my camera platform with one of the "pots" on the 9xr.  and I bought a gimbal motor (Ipower 2208) to do this and I want to avoid having to mess with a gimbal set up.  I could have just mounted it on a servo but I really like the…
Apr 24, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham,

Weather permitting I am going to try to run until it triggers again, but this time with the current enable in the logs and see if I can determine what is really triggering it.

It may be a week or two as I am leaving for vacation soon. …"
Apr 20, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham,

I will try to add two screen shots.  The first will be of the 1/2 amp battery reserve entry.  The second will be of the explanation of this in the Full Parameters. 




SORRY this one is a bit hard to read, hopefully it will expand enough…"
Apr 20, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham,
Thank you for that graph.  I had not seen it  before.  I had always read that 3.3 was the limit that you need to "shut down" to avoid damage to the Lipo.  This shows differently.
BUT, the hard part for me is determining why my quad dropped…"
Apr 20, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham,

I think I just realized that there are other battery warning settings on the power module site that probably need to be reviewed.    I hope to get to that this weekend.

http://copter.ardupilot.com/wiki/common-measuring-battery-voltage-a..."
Apr 14, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham,

Thanks.  A few clarifying questions.  It has a place to enter a low voltage.  I entered 9.8 for my 3 cell lip.  It also has a place for the reserve amount of amperage you want to keep before FS triggers, which I set for half an amp.  on a…"
Apr 14, 2014
Charosenz replied to Charosenz's discussion Batt FS triggering too soon, any ideas appreciated
"Graham, Dave,

Thanks guys for the feedback.

I too wondered if it was tied to the current and not voltage.   I have mine current set to trigger at 1/2 an amp which is the lowest value you can use and I know it was not down to that value when the FS…"
Apr 13, 2014
Charosenz posted a discussion
I have my battery failsafe set to trigger at 9.8v.   BUT it actually triggers at a much higher voltage, today it triggered at 10.64vHere is a graph showing it.
Apr 12, 2014
Charosenz replied to Tom Mahood's discussion Any good GPS cameras lighter than a Canon SX230 HS?
"Tom,

Good question.  I am thinking of getting in to AP and if you don't mind, I was curious to know when you use this camera with chdk does this also require an IR light to trigger the photo? 

I hope that is not too off topic, if so, I apologize."
Apr 10, 2014
Charosenz commented on Thanh Nguyen's blog post Low cost version of APM2.5
"Super, thanks for sharing.  I just want to confirm it is 8bit processor, right?"
Apr 10, 2014
Charosenz replied to Oliver Volkmann's discussion Configuring "A9" on APM2.5 for Camera Trigger with StratoSnapper
"Thanks!  Good info."
Apr 10, 2014
Charosenz replied to Oliver Volkmann's discussion Configuring "A9" on APM2.5 for Camera Trigger with StratoSnapper
"Ravi,

Are you using a servo to manually push the camera trigger button on the camera to take a shot and entering this command in the MP waypoint list?  Or?

I am still debating on using the chkdsk method of camera trigger with cannon cameras or the…"
Apr 8, 2014
Charosenz replied to Colin's discussion Unexplained flip and crash in auto mode
"Colin,

I did look at the logs.   The only thing I see a bit weird, is the current drops quite hard just before you switched to loiter.   see it in this screen shot?   See it also happens just before the roll begins.  Not sure what to make of…"
Apr 7, 2014
Charosenz replied to Colin's discussion Unexplained flip and crash in auto mode
"WOW, sorry to hear that.  The good news is that it seems to be tied to Mission Planner if it truly only happens in Auto mode.    Was it the same mission or a new one?

I have not looked at the logs yet, but I would strongly suggest you do an…"
Apr 7, 2014
Charosenz replied to Colin's discussion Unexplained flip and crash in auto mode
"Good to know.     If you could add the motors to the logs that may help see if there was some anomaly with one of them that caused it in the future.   Like a loose connection or a sporatic value from the esc  etc.   Last time this happened to me I…"
Apr 5, 2014
More…