About

Gender

Male


Location

Hampshire, IL


About Me:

Embedded Firmware Engineer, GPS and IoT clive1 @ stm32 and ublox forums cturvey @ open maps and ublox raw


Please tell us a bit about your UAV interest

Low cost GPS RTK and Post Processing


Hometown:

Hampshire, IL


Activity Feed

Clive Turvey commented on DROTEK's blog post U-Blox M8P Integration done!
"@Nikola I've been talking to u-Blox about RTK for over a year. I didn't really want to mod my Drotek XXL M8T, but they conveniently have the serial TX/RX and power headerized so connecting it to a HM-TRP (3DR) type radio would be a breeze. And it's…"
Apr 20, 2016
Clive Turvey commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"There are 2 that are currently under going in-orbit testing, and another 4 under going ground testing pending launch."
Feb 20, 2016
Clive Turvey commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"From a south facing window sill I've had 3.01 pull in a maximum of 28 satellites across the GPS, GLONASS and GALILEO constellations using a generic mag mount antenna, and similar results with an external Garmin GA38, and in general upper 20's for a…"
Feb 20, 2016
Clive Turvey commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"Ok, the Galileo signals share the same band as GPS, so if you have a GPS+GLONASS set up now, Galileo will be workable. You must enable Galileo via the CFG-GNSS command, and burn that in if you want it to stick. Also I believe there is a 3Hz…"
Feb 20, 2016
Clive Turvey commented on Melih Karakelle's blog post OpenBee: an OpenSource Telemetry Module with Xbee footprint
"@Melih, Sorry for animating this thread, but I stumbled upon it looking for something exactly like your HM-TRP on XBee board from the September 18, 2012 at 1:51pm post. Not sure if you still have any of those boards, or some related info. Thanks."
Feb 15, 2016
Clive Turvey commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"@Nikola, Well the NEO-M8P has finally been announced publicly, offering GNSS RTK
http://goo.gl/TjpBc2"
Feb 15, 2016
Clive Turvey commented on Gabor H's blog post Galileo arrived with recent FW update for u-blox 8 series users
"@Cala The 3.01 firmware works with the NEO-M8N and LEA/NEO-M8T. I've used it on several M8N modules, and on the NEO-M8T in the Drotek XXL. I've conversed and shared data with a couple of others who have M8T modules. You have to enable Galileo with…"
Feb 14, 2016
Clive Turvey commented on Gerard Toonstra's blog post Cheap 1-2cm (scale) accuracy for your surveys
"The 3.01 firmware does not disable raw output, it changes the parameters and obfuscates things slightly.
The 2.01 (ROM/EXT) continues to function, so unless you have some compelling reason to use the unvalidated Galileo constellation you can flash…"
Feb 7, 2016
Clive Turvey replied to Mahanth Gowda's discussion UBX-RXM-RAWX messages getting dropped
"Dean,

Only the M8T (2.30) firmware can generate RXM-RAWX, all M8 can generate TRK-MEAS.

The MAX-6Q should be able to generate RXM-RAW, but you have to do two things, a) send a firmware version specific command to enable them, and b) send a CFG-MSG…"
Dec 31, 2015
Clive Turvey commented on Gerard Toonstra's blog post Cheap 1-2cm (scale) accuracy for your surveys
"ALL current uBlox offerings can output 'raw' measurements, the M8N via TRK-MEAS, only the M8T has the RXM-RAWX which is the officially blessed manner to get RINEX polished data."
Dec 22, 2015
Clive Turvey commented on Gerard Toonstra's blog post Cheap 1-2cm (scale) accuracy for your surveys
"I've used these Duinopeak NEO-M8N GPS Shield for Arduino with Antenna mashed together with STM32 Nucleo and Discovery boards to record hourly RINEX observation files directly to a Micro SD card.

The TCXO's in the M8N series parts offer much better…"
Dec 22, 2015