About

Gender

Male


Location

Conroe, TX


About Me:

New to hobby, interested in building my own quad.


Please tell us a bit about your UAV interest

I currently have a Blade NQX and a MQX and want to get into something a little bit bigger. I want to build my own mainly for Trick flight and some video shooting.


Hometown:

Conroe, Texas


Activity Feed

Cody Castilaw left a comment for Cody Castilaw
"Awesome I am glad it could help you out. Its been awhile since I have had to mess with that stuff but I am glad to know it's still helping people. Good luck with your flying!"
Aug 25, 2015
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"Hey e left, what I found is that you are correct if you do not plan to provide power to the back railed then you do not need the BEC. I already had mine so I still use it as a backup power to the flight controler incase something happens. I did not…"
Aug 5, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"Try going lower on the throttle I think mine was a good bit under.  In my research I had found that the beep that it does means no signal to ESC.  This is because the flight controller cuts off signal during the arming phase until two things happen.…"
Jul 5, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"The reason that mind did this was because the signal from the throttle on the TX was above 1000 once I adjusted it to below 1000 I was able to arm the quad.  I believe I have documented this on the post or another.  If you have trouble adjusting the…"
Jul 4, 2014
Cody Castilaw replied to Cody Castilaw's discussion First Quad Build looking for advice
"I am glad this could help you.  Feel free to ask me any questions you might have, I am always willing to help.  I have been flying mine for awhile now and I LOVE IT.  "
Mar 17, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"They alarming beep means that the signal they are getting says the throttle is not all the way down. Make sure your trasmitter is on and bound with the rx when u turn everything on. If it is then you might need to adjust your travel percent on the…"
Jan 26, 2014
Cody Castilaw commented on Felix Meissner's blog post setting up 6 different flight modes on a Spektrum DX7 using just one channel
"Ok guys I finally got my 6 modes working.  This is what I had to do.  And if anyone can tell me that this isnt a good way to do it please fill free.
Under Travel Adjust I set Gear to +93% and -22%
Under Flap Sys I set
Norm Up 100%
Mid Dn 50%
Land Dn…"
Jan 25, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"Made a quick video on what the arming process sounds and looks like, hope it helps someone else.  
https://www.youtube.com/watch?v=1brS2hI7NdU&feature=youtu.be"
Jan 24, 2014
Cody Castilaw replied to Cody Castilaw's discussion First Quad Build looking for advice
"So I am back and I have been busy!   I hope to be able to do a full write up on this build but I just wanted to share where I am at.   
So over Christmas I have gotten most of the parts needed to build my quad, all I needed was the flight…"
Jan 24, 2014
Cody Castilaw commented on Felix Meissner's blog post setting up 6 different flight modes on a Spektrum DX7 using just one channel
"Fred-  Yes I am in Acro Mode and followed the directions on a new setup to the T 3 different times and still if I watch the switches in Mission planner I can see Channel 6 move but Channel 5 only moves when I move the gear switch.  When I set the…"
Jan 24, 2014
Cody Castilaw commented on Felix Meissner's blog post setting up 6 different flight modes on a Spektrum DX7 using just one channel
"I know this post is old but I am having issues with my DX7 and 6 modes.  I finally got it to do 4 modes but I have to use the Gear, Mix, and 3 pos flap switch to do it.   When I follow the above directions chan 6 in mission planner will move around…"
Jan 24, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"Woot!!! The quad motors are spinning!!!  

So Issue One- Remote binding Pitch stick to both Pitch and Throttle in Mission planner.
Resolution.  Connect FC to the CLI console.  Erase FC.  Reset FC.  Rebind remote and calibrate.  This fixed this for…"
Jan 23, 2014
Cody Castilaw replied to Cody Castilaw's discussion New Pixhawk with DJI F450 kit- Motors Beeping
"Oh I am also using Arudcopter 3.1 firmware.  I read that someone had an issue when they updated and went back to 2.9 and it fixed it.  Could this have something to do with it?   I did change the firmware to Arduplane and has the same results.  "
Jan 23, 2014
Cody Castilaw posted a discussion
ok, so I currently have setupThe Pixhawk FCA 5V BEC4 DJI 30 AMP ESC OPTO4 DJI 920 MotorsTBS Discovery PlatesSpektrum DX7 for remoteSpectrum Satellite receiver plugged directly into the FCEverything was going fun until I tried to hook the ESCs and…
Jan 22, 2014
Cody Castilaw replied to Cody Castilaw's discussion First Quad Build looking for advice
"Hey everyone,  
    So I know it has been awhile but I wanted to give a status update on this build.  I was told I had to wait until after Christmas to build this baby and I have waiting long enough.  I have some of my parts ready to go but I need…"
Jan 8, 2014
Cody Castilaw replied to Cody Castilaw's discussion First Quad Build looking for advice
"Gary m, 

 Thanks for the great info and Links I will be sure to take a look over all of this and repost my new build list.  "
Sep 25, 2013
More…