Gender
Male
About
About Me:
I am an electronics technician, I have a workshop aircraft. I am a private pilot, flight instructor and model aircraft pilot.
Please tell us a bit about your UAV interest
Recently in my company we have started to build uav for hobby and professional use.
Hometown:
Budrio (close to Bologna)
Activity Feed
"Where is the "zero home altitude" button in mission planner ?
Thanks,
Fausto"
Thanks,
Fausto"
Hi all,I'm trying to find an amplifier to boost two-way telemetry 3DR. Does anyone know where you can find one?Cheers, Fausto
"Hi Tridge,
I noticed that when turning on the APM board, the compass indicator is reset on the North position independently of the direction where the plane is oriented. For example, if the plane is oriented at 90 ° or east when i boot the APM the…"
I noticed that when turning on the APM board, the compass indicator is reset on the North position independently of the direction where the plane is oriented. For example, if the plane is oriented at 90 ° or east when i boot the APM the…"
"You are a great Tridge !
This week I'll try the new features.
Fausto"
This week I'll try the new features.
Fausto"
"Hello elad,
nice job, congratulations.
I am going to get some ideas to make a similar job with my old laptop.
Fausto"
nice job, congratulations.
I am going to get some ideas to make a similar job with my old laptop.
Fausto"
"Hello Terry,
in stabilize mode it is normal that the rudder moves in the direction of the turn.
The mixing rate is controlled by the parameter "KFF_RDDRMIX".
You can adjust the parameter in the apm parameters table:
The value of the adjustment range…"
in stabilize mode it is normal that the rudder moves in the direction of the turn.
The mixing rate is controlled by the parameter "KFF_RDDRMIX".
You can adjust the parameter in the apm parameters table:
The value of the adjustment range…"
"Hello Søren,
we have accelerometers on the APM board, I think it is enough to read a peak higher than a certain value of "G" to establish that the aircraft collided with an obstacle or the ground.
Of course is important to filter well the reading of…"
we have accelerometers on the APM board, I think it is enough to read a peak higher than a certain value of "G" to establish that the aircraft collided with an obstacle or the ground.
Of course is important to filter well the reading of…"
I have not understood the behavior of the function that activates the engine during auto takeoff. In my case after hand launched the model, just above the threshold speed the engine will start automatically.I read that someone however the engine…
"Hello all,
I confirm that I could not find the parameter that defines the start of the engine for automatic takeoff.
In my case the engine starts when I launch the model at hand when it reaches a certain speed, I think 3m/s in accordance with the…"
I confirm that I could not find the parameter that defines the start of the engine for automatic takeoff.
In my case the engine starts when I launch the model at hand when it reaches a certain speed, I think 3m/s in accordance with the…"
Hello all,I mounted my APM2.5 on a Bixler to test the hardware and learn how to program the various parameters before trying them on a bigger model.Yesterday and today I made several flights to test the various modes stabilize, fbw, rtl, etc.In the…
"Thanks for suggestions,
I found a diagram of a converter PPM> USB with the source code. I'll try to build it then I will see the performance.
My intent is to have a good range of the radio link with a directional tracking antenna on 433 MHz, perhaps…"
I found a diagram of a converter PPM> USB with the source code. I'll try to build it then I will see the performance.
My intent is to have a good range of the radio link with a directional tracking antenna on 433 MHz, perhaps…"
Hello all,I was thinking about the possibility to connect the transmitter to the pc to control the model through telemetry.For example, use a normal remote control at 2.4 GHz, which transmits the signal to a receiver connected to the pc, placed a…
