Hi
When I try to connect to APM 2.5 it does not work.
notes:
Com port is correct.
power is present (LEDs are flashing)
I can upload the actual firmware to the APM 2.5 board and it works.
What can I do?
Is this a known bug?
regards
Franz
Read more…hi
build a new hexacopter made of carbon.
The goal is to simple take images with the canon g11.
It is build of 18mm carbon tubes. The diameter is 90cm. The top plane is 1mm and the bottom plate is 2mm cfk (diameter of center plate is 250mm). I use 12"
Read more…HiMy next hexacopter shlud be something professional. I wand an uavframe or a self made carbon tube frame.The goal is to build a hexacopter to carry a camera like the canon g11. The diameter should be 80cm.Uavframe: one peace carbon,700€, very stable
Read more…Hi
My actual hexacopter has got a weight of 2.2kg with accu and I want to reduce the weight but keeping the same stability (in future i want to carry another 900gramm, that is a camera and the camera mount):
At the moment the aluminium tubes have 15x
Read more…Hi
I found that my copter makes an accelerator leveling at every power up.
This is a problem!
The cause is that then at every start up I need a very flat area for leveling. But I do not have this very flat area. So I bought a very little water level
Read more…Hi
I had a bad crash after I switched my Rc controll off! This was a mistake of mine.
What happend was that the quadrocopter stopped all the motors and so it dropped from 20m height.
why does it switch off the motors? A very slow decrease (rough landi
Read more…hi
I like Arducopter!
with the new frame (15mm alu, 350mm motor distance) and the 12" props it was a pleasure to fly it!
Very very stable!
thank you all!
with best regards
Franz
Read more…HiWhen i arm or disarm the motors it would be a good idea to have a beeper instead of the leds ( or aditionaly)Advantages:- if electrinic is housed one can. Not see the leds- if the sun is very shiny i can not see the leds.What do you think? Are ther
Read more…hi
After some good flights and several very bad crashes (a lot of motors and frames) I rebuild my hexacopter (15mm aluminium, housing for the electronics,....)
It took me 2 day to do that.
Today I was flying with 2.0.45 and it was good. A little nervo
Read more…Hi
I have the following setup and I think that the esc get too hot: 50-60degrees
6x Keda 20L22
6x 10x4.5 props
6x Hobbyking HK30 with 25 A permanent current possibility
3s 5700 Lipo
Canon C11 camera
58cm fram with 10mm alu
2kg averall weight with lipo and
Read more…Hi all,
I now work with the new software version 2.0.40. It works fine for stabilize.
When I switch to simple the copter starts climping very fast. I than quickly switch back to stabilize. the hex comes done again.
I thought that simple does only cor
Read more…Dear all,
Wen I use the USB cable I can communicate with my hexa: no problem
When I use the XBee I have problems:
- The user interface react very slow
- the terminal shows crc fail: "NavLink Bad Paket (Crc Fail)" very often: several times a second.
I u
Read more…Hi
am new here with arducopter. And I think i am too stupid for it:
I fly a hexacopter (arducopter) for 4 weeks and it is fun but I crash it very ofter. I had the following problems:
1. lost a prop in 50m heigth: full crash, 2 Motors broken, 5 props b
Read more…