About

Gender

Male


Location

Catania


About Me:

I'm Giuseppe from Catania (Sicily) and simply I love multirotors selfmade.


Please tell us a bit about your UAV interest

My real job is really different from this wonderful technology, and for me is just a fantastic hobby.


Hometown:

Catania


Activity Feed

Giuseppe D'Angelo replied to Larry A Amati's discussion taranis & x8r setting failsafe for signal loss
"This should be can help
https://www.youtube.com/watch?v=woT_9tXkWhU
Ciao - Giuseppe"
Dec 18, 2014
Giuseppe D'Angelo commented on ctech4285's blog post EPM Cargo Gripper. Simple easy method for gripping and relasing cargo on a copter
"I just bought it to try it with my lady Pixhawk !"
Nov 10, 2014
Giuseppe D'Angelo replied to Henri's discussion Skycat parachute launcher for Drones
"well done.
will you do a version for 6mq/12mq parachute ?

Ciao - Giuseppe"
Oct 30, 2014
Giuseppe D'Angelo replied to Carl Davis's discussion Crash due to motor/esc failure?
"What esc/motors are you using ?
What propellers are you using ?What total weight of quadcopter ?It seems a loss of sync esc/motor nr. 1 but, I see your Throttle out/in seems more than 60%
Too much boost could have caused lost of sync.

I think the…"
Oct 3, 2014
Giuseppe D'Angelo replied to Henri's discussion Skycat parachute launcher for Drones
"Hi Randy, I read about parachute support only with Pixhawk and from 3.2x.
I see on mission planner, on page / extended tuning / ch7 or ch8, three options for opening the parachute.
Can you explain these options and their differences ?

Ciao -…"
Jun 28, 2014
Giuseppe D'Angelo replied to Henri's discussion Skycat parachute launcher for Drones
"Hi Henry, your work is really interesting and helpful, I will follow you from last year and I finally decided myself to experience a parachute Opale on my multicopter.
My problem is that, since I am a modeler and not a professional, I do not have…"
Jun 22, 2014
Giuseppe D'Angelo replied to Nayden's discussion Loiter goes straight ahead and crash
"I looked at your log and are not those default
Theese are default:"
May 30, 2014
Giuseppe D'Angelo replied to Nayden's discussion Loiter goes straight ahead and crash
"first: put batteries under frame, your center of gravity seems higher than motors.
Second: try with default PID, and try stabilize and Althold. Your stab_P is too low,  Don't use loiter if you don't see good result in stabilize and althold.
If your…"
May 29, 2014
Giuseppe D'Angelo replied to Randy's discussion ArduCopter-3.1 released!
"Hi Ravi, try first Motorsync with Pixhawk/Afro/motors.
might be useful to find out sync issue with your esc's.
Do you use ground of PWM signal connected ?

Ciao - Giuseppe"
May 26, 2014
Giuseppe D'Angelo replied to Randy's discussion AC-3.1 autotune support discussion
"Today first Autotune on Pixhawk with firmware 3.1.4, esc's AFRO30a (with ground connected ;-)) T-motors MT2216-900kv, props Graupner 11x5, frame clone Mikrokpter XL2 (square frame), batteries 4s, total weight 3.9Kg.
1.10 minute fot roll 1.30 for…"
May 25, 2014
Giuseppe D'Angelo replied to Randy's discussion AC-3.1 autotune support discussion
"Today my first autotune with Arducopter 3.1.4 on APM 2.6, esc's 40a SimonK, MK3638 motors, props APC 12x3.8, 4s battery and total weight 3.5Kg.
1,30 min for roll, 1.30 min for pitch. Why it was so fast ?
I like final result, very smooth flight.
here…"
May 24, 2014
Giuseppe D'Angelo replied to Miguel Garcia Almeida's discussion PixHawk 3.1.4 - Help me analyse this crash - X8 craft
"My opinion that adapter could be cause of reboot.
you need remove the heat shrink and check the weildings
the best thing is to buy separate components (xt60 male fmelae AWG12 silicon cable) and create the adapter you.

Ciao - Giuseppe"
May 21, 2014
Giuseppe D'Angelo replied to Miguel Garcia Almeida's discussion PixHawk 3.1.4 - Help me analyse this crash - X8 craft
"Why do you have double powered ?
For redundancy, OK, but... are you sure double powering (power module + ubec) is right for pixhawk ?
Pixhawk does support elettricaly this configuration ?
I don't know this answer, but my opinion  it does not seem…"
May 21, 2014
Giuseppe D'Angelo replied to Miguel Garcia Almeida's discussion PixHawk 3.1.4 - Help me analyse this crash - X8 craft
"seems lost powering connection on fly.
From log: Pixhawk turn off and no longer recorded logs  .. on fly (alt and all other log  stopped to above the ground)
My opinion: You need to carefully check the powering connections (XT60 male - female…"
May 21, 2014
Giuseppe D'Angelo replied to Randy's discussion ArduCopter-3.1 released!
"I see now :
ArduCopter 3.1.5-rc2 20-May-2014
Changes from 3.1.5-rc1
1) Bug Fix to broken loiter (pixhawk only)
2) Workaround to read from FRAM in 128byte chunks to resolve a few users boot issues (Pixhawk only)

I just looked on mission planner…"
May 20, 2014
Giuseppe D'Angelo replied to Randy's discussion ArduCopter-3.1 released!
"My opinion: mechanical failure or.. powering problem (vcc too low, are you powering from internal "bec esc's ?)

Ciao - Giuseppe "
May 18, 2014
More…