About

About Me:

Researcher in Physics.


Please tell us a bit about your UAV interest

I have been flying (short-range) FPV with an Easystar clone for some time, and I am now installing an auto-pilot (ArduPlane + CRIUS AIO Pro) in my plane.


Hometown:

Gif-sur-Yvette


Activity Feed

GrMis commented on Christiaan van Vollenstee's blog post Hobbyking 500mw telemetry 433/915
"Hi. Someone (skelator) on the HK product page claims that this modem is based on the following RF module:
http://www.dorji.com/docs/data/DRF4431F27_DRF4432F27.pdf
Similar to the older Si4431, but with higher output power (27dB/500mW). "
Mar 27, 2015
GrMis commented on Christiaan van Vollenstee's blog post Hobbyking 500mw telemetry 433/915
"Hi. I am also wondering what is inside... Could this modem use a YS-C20L module ?"
Mar 24, 2015
GrMis replied to Jérôme Niklès's discussion MinimOSD - Black screen/no image
"This is not correct: in the minim OSD the video_in and video_out are separate pins and  they are not connected.
If the maxim chip is fried (or just not powered), you get no video signal at all."
Mar 29, 2014
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Hi Jon Sogi,Perhaps this answer comes too late... but anyway here are some of the parameters you may check/set  in the APM_confi.h:


#define CONFIG_APM_HARDWARE  APM_HARDWARE_PIRATES#define PIRATES_SENSOR_BOARD PIRATES_CRIUS_AIO_PRO_V1

// uBlox…"
Jun 24, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"I don't know... perhaps some #define is  incorrect ? Do you have
#define CONFIG_APM_HARDWARE APM_HARDWARE_PIRATESin APM_Config.h ?(most recent code: http://code.google.com/p/megapirateng/source/browse/branches/ardupl...)"
Jun 14, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"I have a v1, so I cannot tell for sure.... But I guess it should be ok."
Jun 14, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Oups, sorry, I meant ArduplaneNG (not ArdupirateNG)."
Jun 14, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Hi. You have to use ArdupirateNG. The hardware of the Crius board is not compatible with the Megapirate code (sensors are connected via i2c bus in CRIUS,  but Ardupilot uses SPI, etc.)"
Jun 14, 2013
GrMis replied to Jérôme Walrave's discussion Minim OSD fried ? no OSD data...
"Hi.
The max7456 chip is quite fragile. As far as i understand, it can easily be killed by slight voltage differences between the analog and digital grounds (or Vcc) for instance.
I already fried too boards... but it is not very difficult to repair…"
May 2, 2013
GrMis replied to Jérôme Niklès's discussion MinimOSD - Black screen/no image
"Hi,
As many of you, I already fried two minim boards (using a single Lipo)...
However I could repair it by replacing the max7456 chip (available as free sample on Maxim website).It is quite straightforward to do, but I posted some details here:…"
May 1, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Yes, I am following that  RCgroups thread too ! But the title is not that explicit, since it does not mention ArduplaneNG :-(By the way, is the "diff" of between JLN's ArduplaneNG and the Arduplane 2.4 available somewhere ? I would like to estimate…"
Apr 3, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Vladimir, thanks for your reply. I am ok with setting the failsafe on the TX&RX side (using trim etc., as you wrote), but I suspect that my problem is on the ArduplaneNG side: If I switch off the TX, the receiver correctly sends a throttle value…"
Feb 20, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Thank you for your reply. My receiver (FrSky) also has a failsafe, so I can certainly do as you suggest.
I though it could be nice to use the built-in 'failsafe' function of the arduplane code, but if you did not succeed either I will probably give…"
Feb 15, 2013
GrMis commented on Jean-Louis Naudin's blog post Autonomous flight mission with the ArduPlaneNG v2.x R5 and AIOP IMU board on Maxi Swift flying wing
"Hi,
I recently decided to equip my FPV plane (easy-star clone) with the CRIUS AIOP board and this firmware. At the moment I am just doing some tests on the bench. So far everything seems Ok except that I have a problem with the Throttle failsafe. I…"
Feb 15, 2013