Gender
Male
About
Location
Rome
About Me:
fun with arducopter ac2, and i like arduino to make software and hardware projects
Please tell us a bit about your UAV interest
arducopter
Hometown:
Rome
Activity Feed
"Hi,
with 2.7.3. APM2 all is working fine, after updating to 2.8.1 all is wrong.. When i fly indoor, my copter goes in any direction, seems that it want to correct and keep the position but it make a spiral that is little and than bigger until i must…"
with 2.7.3. APM2 all is working fine, after updating to 2.8.1 all is wrong.. When i fly indoor, my copter goes in any direction, seems that it want to correct and keep the position but it make a spiral that is little and than bigger until i must…"
Hi, could you suggest me the best servo for a gopro gimbal? i use hitec hs55 but are not so much reactive. I try the savox sh0264mg but they are baddest servo i ever use!!! I want to use an high speed micro digital servo but smooth like analog. Any…
"Mission planner says "ARMED" but if i up throttle, motors won't start. 2.7.3fw
Why?
How to resolve?"
Why?
How to resolve?"
"Hi, i fly with a hexa and apm1 fw 2.7.1 Stabilized fly is great but when i switch to loiter mode i get many wobble with and without wind. I try to decrease Rate Loiter P and Speed Loiter P but wobble are always.
Any suggestions? how can i do?
thanks"
Any suggestions? how can i do?
thanks"
"Hi,
i need help to know what to do to resolve this problem... See this video:
https://www.youtube.com/watch?v=1XfARq98-jk
what could be? hear the motors spin up sometimes.. (at 0:49 sec)"
i need help to know what to do to resolve this problem... See this video:
https://www.youtube.com/watch?v=1XfARq98-jk
what could be? hear the motors spin up sometimes.. (at 0:49 sec)"
Hi,i don't know how to say... my arducopter fly very well but sometimes it spin up motors for 1/2 seconds when hovering and i don't know why. I made a video, check the sound and the movement at 49 seconds. I check all connection between motors esc…
"Hi,
i'm using fw 2.5.5 and my quad fly very well. Only one question... there is a way to set a min altitude? (i'm using sonar). Because i fly in fpv, many time i go too much down and in fpv is hard to see the altitude, so if i set a min alt like 1,5…"
i'm using fw 2.5.5 and my quad fly very well. Only one question... there is a way to set a min altitude? (i'm using sonar). Because i fly in fpv, many time i go too much down and in fpv is hard to see the altitude, so if i set a min alt like 1,5…"
"yes, i've these motors. Thanks to all for the info !!
More mistakes, more experience i get :)"
More mistakes, more experience i get :)"
"ok, i will try, but i read in some forum that with 1100kv motors i must use 8x4 propellers. It's right? Or I can use all type of propellers if balanced?"
"Alex, I have Tiger motor MT2208-18 1100kv.
Ellison, I haven't balance the propeller in both cases, but i tried 8 propellers of 10x45 and the results are the same in vibrations and noise"
Ellison, I haven't balance the propeller in both cases, but i tried 8 propellers of 10x45 and the results are the same in vibrations and noise"
I did't know how much important is choose the right propellers, but after changing on my multiwii and arducopter (3dr) i get no vibrations and fly very well :) this is the video: http://youtu.be/CzirPZl1Jnw
"Hi,
what value i must change to get stable ATL HOLD?
My config is: Quad 3DR frame set to X, esc from diydrones store, T-motor 2208, 10x45 propellers, sonar.
With the default pid for alt hold when i fly under 1 meter and activate alt hold the quad…"
what value i must change to get stable ATL HOLD?
My config is: Quad 3DR frame set to X, esc from diydrones store, T-motor 2208, 10x45 propellers, sonar.
With the default pid for alt hold when i fly under 1 meter and activate alt hold the quad…"
hi,i try the new firmware in acro mode and my arducopter roll to left so much and i can't take off.when i try to fly in stable mode it fly very well but i think i must correct the acro mode stability.any suggestion?
Hi,still there and i'm sorry for that but i'm really newbie... My quad rotor won't found so that i made a new one. I use the same receiver and transmitter to control it and same batteries but all the other parts are new, esc, motor, frame, power…
"cannot resolve! please say me what i must do, i'm very much frustrated!!!! i cange ALL parts.. i buy another apm kit presoldered but nothing :(((
"
"
