About

Gender

Male


Location

London


About Me:

Video editor and motion graphics designer.


Please tell us a bit about your UAV interest

I am using a DJI F550 for aerial filming and currently building a larger Octo with Pixhawk.


Hometown:

London


Activity Feed

Jamie Nelson posted a discussion
I have set my thr_min at 165 mid at 400 and max at 800After arming the props seems to spin correctly at about 165. If I then raise throttle off zero nothing happens until about 30% when it suddenly shoots up into the air. (Except this is a bench…
Jun 26, 2015
Jamie Nelson posted a discussion
I have had a few 'successful' flights - by that I mean buzzing around a bit without crashing. I then got the toilet bowl effect and nearly crashed. I managed to flip into stabilise and land ok. My aim in the future is to add expensive and…
Jun 23, 2015
Jamie Nelson replied to Jamie Nelson's discussion Updated to Mission Planner 1.3.29 now my settings are all messed up.
"Many thanks for that resource.
I've tried an older version and still have the same problem so it's something else causing the blank pop ups. Maybe my machine. I have luckily found that OSX's APM software does what I need. I had thought it had a lot…"
Jun 22, 2015
Jamie Nelson posted a discussion
I have just updated mission planner following a prompt. When I restarted all the settings were set to zero. I could't recover anything and so I selected reset all settings.I then redid compass etc and tried to reprogram the 6 flight modes.There are…
Jun 18, 2015
Jamie Nelson replied to David Pulvermacher's discussion Using 12v equipment with 4S batteries in ArduCopter User Group
"You could have a smaller secondary 3s battery on board for that. Or you could split the voltage using a simple voltage divider circuit made of a couple of resistors. Alternatively there may be a BEC component you can add to drop the voltage?"
Jun 17, 2015
Jamie Nelson posted a discussion
I have set up octo and it seems quite stable and easy to control. I haven't done any tuning.In the 2 modes I have tested the vertical speed doesn't seem right. In Stabilize if I move the throttle up fill it shoots up like a bullet.And in loiter mode…
Jun 16, 2015
Jamie Nelson posted a discussion
(previously posted in pixhawk hardware - now moved to this forum as it seems more suited)I'm trying to resolve poor compass interference, possibly due to using the pixhawk internal compass rather than external. Currently getting bad readings outside…
Jun 12, 2015
Jamie Nelson replied to Jamie Nelson's discussion Copter won't ascend in alt hold or loiter
"Thanks for the input. I have resumed work on this now. Sorry for the late reply. I upped the power and so now the full throttle sends it bolting upwards in stabilise mode so fast. (I know it will be much less with camera payload).
Conversely…"
Jun 10, 2015
Jamie Nelson replied to Jamie Nelson's discussion Adding servo to aux channel 1 - How do I do it?!
"Thanks. I'm returing to this after a break. I'll take a look. cheers."
Jun 10, 2015
Jamie Nelson replied to Jamie Nelson's discussion Toiletbowl issue and how to fix it.
"This seems to show something. This graph compares throttle to magnetic interference. The base magnetic field is 400 but then spikes up to 600 when throttle is applied. 
My pixhawk came with what i think might be a cheap GPS module. It did work ok…"
Jun 10, 2015
Jamie Nelson replied to Jamie Nelson's discussion Toiletbowl issue and how to fix it.
"OK got the test running but it shows interference as zero which isn't right."
Jun 10, 2015
Jamie Nelson replied to Jamie Nelson's discussion Toiletbowl issue and how to fix it.
"Thanks Bill. I think I need to run compass mot test. I have currently got my current going direct to my tx telemetry and not into the pixhawk. So the readings might not work unless I have the current there too? "
Jun 10, 2015
Jamie Nelson replied to Jamie Nelson's discussion Toiletbowl issue and how to fix it.
"Hi Patrick,
Yes I think the pixhawk has an internal compass. If I rotate the GPS module the heading does not change on mission planner. But if I move the pixhawk it does change. I am getting some kind of GPS and compass readings as it seems to have…"
Jun 10, 2015
Jamie Nelson posted a discussion
I flew a few months back and crashed due to brown out. I have now beefed up the cable and done a new flight test. In loiter mode it is showing bad toilet bowl effect. Moving in wider and wider circles.I read through some stuff and found that compass…
Jun 8, 2015
Jamie Nelson replied to Chris Woods's discussion Compass interference and graphing mag_field
"I was puzzled about this too. I found that the pixhawk will log 2 types of data. 1 type is saved on the onboard memory card. This is the logs you are looking at. The other logs are telemetry logs which are saved to a laptop via bluetooth. This page…"
Jun 8, 2015
Jamie Nelson posted a discussion
I've been stuck on this for a while. How do you set up a spare channel to run a servo through the aux outputs?This is what I have tried:Go to APM planner > Initial setup icon > Optional setup > Camera gimbalThen assign 'Tilt' to RC9 and set input…
Jan 25, 2015
More…