Good day all
I am starting a review of the mini pix flight controller which is a small version of teh pixhawk from
radiolink. If you want to watch:
https://www.youtube.com/watch?v=Pl1IMOQLBAk
This is my first video and I would like to improve by using a
Read more…Good day all
I have a quad ( pixhawk 2.4.8 ) runing Copter 3.5.5 on a 450 frame. I can fly my drone with a joystick
via mission planner, but I find that the sensitivity is very high. It is a Logitech 3 axis joystick and I have
been adjusting the settin
Read more…Good day all
Just completed a very basic ( I have to say ) hexacopter. Just a FC, radio and GPS.
But a start non the less !!! It was a success ... all I did was fly it in stabilise mode by hand.
I shall now into a range of tests, testing all the auto-fu
Read more…Good day all
I have completed my F450 copter with a pixhawk 2.4.8 a month or so ago.
Setup :
F450
pixhawk 2.4.8
APM copter 3.5.5
R_XSR receiver
BL-Heli 32 ESC ( 40 A)
All went well and I completed all the tests : i.e. waypoint flights, RTL, failsafes...
all o
Read more…Good day all
My 450 drone is flying and I have tested most of the autopilot functions. I have flown it with Mission planner on my laptop. Now I want to fly it with either MissionPLanner or QGroudcontrol on a cellphone. (iOS).
My Huawei P9 Lilte does no
Read more…Good day all
I completed my second drone a week or two ago and I thought it was finished !!! Hehe ... !!
a Few days ago I decided to add obstacle avoidance on and I found some information about that.
Enough to get me going.
What I was wondering ..... i
Read more…Good day all
The first 2 phases of my second drone is complete. I now have:
F450 frame
2312 motors
Bl-Heli32 (40A) ESC
9450S props
RXSR Frsky receiver
Pixhawk 2.4.8 ( running APM copter V3.5.5 )
M8N GPS
CADDX Turbo SDR1 1200TVL camera
TBS Unify Pro 5G8 HV Race
Good day all
As you may have seen on other discussions, I have completed phase-II of my second drone.
Just to recap my setup:
F450 frame
2312 motors
Bl-Heli32 (40A) ESC
9450S props
RXSR Frsky receiver
Pixhawk 2.4.8 ( running APM copter V3.5.5 )
M8N GPS
CADDX T
Good day all
I am busy building my second drone :
Setup:
pixhawk
2312 motors
9450 propellers
M8N GPS
RXSR receiver
I have done a successful maiden flight, but I would like to test some of the autonomous
flight modes as I have programmed into the pixhawk. I am
Read more…Good day all
Busy buidling my 2nd drone.
Using a pixhawk and would like to get clarity on the RTL function.
I have seen many videos on the RTL function so I know what the drone does.
My question is about the activation of the RTl mode. If I program chann
Read more…Good day all
I have started building my pixhawk drone and purchased the pixhawk, receiver, ESCs and GPS today.
Connected switch, buzzer and GPS to pixhawk. Did the flashing of the software. Completed the calibration of the accs and the mags. Get to the
Read more…Good day all
Busy building my second drone. Wanting to use a pixhawk with APM software. And since I am new, I have been reading up about this before I go out and buy stuff. One thing that I want to ask - maybe
I just missed it in the docs - ....
Once I
Read more…Good day All
I only have a few months of experience in the RC world. I have completed my first drone : 211-frame. 2206-2500kv motors. Betaflight F4 FC. I added a GPS and BARO and also FPV using the built-in OSD on the FC. Oh... 5040-props.
Next I would
Read more…