About

Gender

Male


Location

Taipei


Please tell us a bit about your UAV interest

身邊目前有APM2.5,Trex450 目前在將APM裝在Trex上


Hometown:

Tainan


Activity Feed

Kun-Wei replied to Kun-Wei's discussion Trex 450 with APM2.5 in ArduCopter (traditional heli) user group
"finally i fixed by changing the mode on the radio and fixed it.
but i have another question is that i download the Arducopter 3.0.1 on the internet and update the firmware by arduino.
however, the setting which i setting by MP are clean.
So , is…"
Oct 31, 2013
Kun-Wei replied to Kun-Wei's discussion 請問誰有將ardupilot裝在飛機上並且可運作的? in Taiwan ROC ArduPilot Group
"結果 只要在APM上將第二個馬達逆轉就好
想請問一下 可不可以把板子上的韌體下載下來
我在網路上下載Arducopter-3.0.1 然而透過Arduino上傳給APM時 所有之前在MP上設定的東西速乎都回到初始情況
所以 我是想 看可不可以將板子上的韌體下載下來 或是 可不可以在MP的資料夾將韌體抓出來?"
Oct 31, 2013
Kun-Wei replied to Kun-Wei's discussion Trex 450 with APM2.5 in ArduCopter (traditional heli) user group
"As Ray say, i fix it by reverse the second servo on mp. 
But there's other problem that my radio's pitch and throttle are separate.
For helicopter, pitch and throttle should be controlled at the same putter.
My flight mode are set as Stabilize,…"
Oct 23, 2013
Kun-Wei posted a discussion in ArduCopter User Group
Hi all, I have a helicopter with APM2.5. I set the board as the wiki. But I got the problem. After starting the APM, the swashplate get slant.  Does any one having get this problem before?
Oct 17, 2013
Kun-Wei posted a discussion in ArduCopter (traditional heli) user group
Hi all, I have a helicopter with APM2.5. I set the board as the wiki. But I got the problem. After starting the APM, the swashplate get slant.  Does any one having get this problem before?
Oct 17, 2013
Kun-Wei replied to Kun-Wei's discussion 請問誰有將ardupilot裝在飛機上並且可運作的? in Taiwan ROC ArduPilot Group
"最近終於用起來
我將接收機與板子連接的線重接 就可以啟動了
現在有個問題想請教
我接上電池後 板子會開始對馬達做初始動作
可是初始過後 被馬達拉動軸彙整個歪掉 (原本平的,可是初始後就歪掉)"
Oct 17, 2013
Kun-Wei replied to Kun-Wei's discussion 請問誰有將ardupilot裝在飛機上並且可運作的? in Taiwan ROC ArduPilot Group
"目前板子上已裝上RC 馬達 GPS 
透過mission planner安裝arducopter v3.0.1 
原本裝上後 我的馬達會開始有動作 
然而目前不知為什麼 馬達沒有動作且毫無反應
而剛剛將yaw右舵打滿 還是disarm的狀態"
Aug 22, 2013
Kun-Wei posted a discussion in Taiwan ROC ArduPilot Group
大家好 如題 我想看一下如何運作我自己有板子跟飛機 可是遇到很多問題 想要請教一下
Aug 21, 2013
Kun-Wei posted a discussion in Taiwan ROC ArduPilot Group
hi all想問各位些問題,之前遇到的問題已經解決了而現在遇到的問題是,在用Mission Planner MAV 1.0的simulation時候抓不到throttle的訊號我已經確認在configuration的遙控器訊號有抓到且正確
May 2, 2013
Kun-Wei replied to Kun-Wei's discussion 關於APM與遙控器的設定 in Taiwan ROC ArduPilot Group
"你好 
又遇到問題了
目前除了throttle 其他都找到了
Futaba ch1 ELE           ch2 RUD           ch3 THR           ch4 AIL           ch5 GEA           ch6 ABK           ch7 AU6           ch8 AU5
各頻道如上
而板子我是依照網站上的 這樣對應 再依照SERVO MONITOR去改,發現我的Futaba的throttle對應到AMP的Radio…"
Apr 17, 2013
Kun-Wei replied to Kun-Wei's discussion 關於APM與遙控器的設定 in Taiwan ROC ArduPilot Group
"抱歉 昨天在忙 想請教一下servo test是需要什麼機器? "
Apr 15, 2013
Kun-Wei replied to Kun-Wei's discussion 關於APM與遙控器的設定 in Taiwan ROC ArduPilot Group
"不知道有沒有設定訊號的地方,像是把得到的訊號指定給所要的動作"
Apr 14, 2013
Kun-Wei posted a discussion in Taiwan ROC ArduPilot Group
大家好小弟想請教大家些問題目前我根據 https://code.google.com/p/arducopter/wiki/ArduCopter?tm=6此網站將APM連接到...,可是遙控器與電腦的連接出些問題,遙控器訊號與Mission planner的訊號是錯誤的,當我遙控器用油門的時候,mp得到的訊號是Roll,其他的軸也是錯誤,不知道各位有什麼解決辦法?
Apr 13, 2013