About

Gender

Male


Please tell us a bit about your UAV interest

FPV player


Hometown:

saint etienne


Activity Feed

Lucas replied to Lucas's discussion Using a power module without BEC daughterboard?
" Your power port should be like that, 2 pins for the GND, the middle one are for the V and I signal and the 2 pins closest to the edge of the board is the VCC. just don't connect the VCC.
I you have a 5v BEC you can connect it to the APM via this…"
Mar 2, 2014
Lucas replied to Lucas's discussion Using a power module without BEC daughterboard?
"My power module is working without the BEC daughter board, just do not plug the Vcc on you APM cause it's feeding 12v instead of 5... I use a separate 5v BEC. This board is used to monitor the V+I of you lipo otherwise you can power the APM via you…"
Mar 1, 2014
Lucas posted a discussion
Hello everybody,Here is my problem, my minimosd is all glitching when I increase the throttle, if the throttle is to high or when my ESC "bip" the minimosd just crash and I need to reboot it via the reset button to have it working.I have two…
Mar 1, 2014
Lucas replied to Clive Moverley's discussion ArduPilot 2.6 External Compass
"You have to go on the parameters list and check around compass properties there is one that allow you that, you should do that before flying. Check on ebay but you can get an external compass for only few $ and it's highly recommended if your using…"
Feb 17, 2014
Lucas replied to Clive Moverley's discussion ArduPilot 2.6 External Compass
"If you don't plug any compass to the APM this one will set the north where you card is pointing at the initialisation (when you plug it to your computer) then you have to enable the compass in the parameters and it will use the GPS for the heading..."
Feb 14, 2014
Lucas replied to Lucas's discussion Using a power module without BEC daughterboard?
"Its working!!!

Cheers!"
Feb 14, 2014
Lucas replied to Lucas's discussion Using a power module without BEC daughterboard?
"Thank you!
I 'm happy to know that I can use that module! I'm gonna use this BEC: 
Apparently it gives a clean 5V voltage...


Thanks for you help I gonna try that today!"
Feb 14, 2014
Lucas posted a discussion
Hello guys,I bought a Power module to have information about power consumption displayed on my OSD, Unfortunately I bought one without the BEC daughter board so instead of supplying the 5v out for my APM it gives me the LIPO out voltage. I haven't…
Feb 13, 2014
Lucas replied to Lucas's discussion External Compas on apm 2.6
"Nobody?"
Feb 11, 2014
Lucas replied to Lucas's discussion APM arduplane : After failsafe throttle stays on
"All good everything works good now!!! I can turn off my tx and turn it on, throttle is ok, I guess It's the ESC calibration that was wrong! the last thing that I don't understand is in RTL mode or stabilized the throttle ll always run slowly even if…"
Feb 11, 2014
Lucas posted a discussion
Hello everybody I bought a Chinese version on the APM 2.6 board with an external compass and GPS The same as on this picture.My problem is the compass is never pointing the same direction even after calibration on the Apm planner.So I decided to buy…
Feb 9, 2014
Lucas replied to Lucas's discussion APM arduplane : After failsafe throttle stays on
"Thanks Graham , i'm gonna check that on mondat:-)"
Feb 9, 2014
Lucas posted a discussion
Hello everybody!I can't figure out what is wrong in my apm settings. When my transmitter is on manual mode or stabilized mode everything works good as it should. I have set the throttle failsafe and here is my problem, if I switch off my transmitter…
Feb 6, 2014
Lucas posted a discussion
Hello everybody!I can't set properly my APM with my easyglider, I'm using flaperon each aileron is controled by a different servo. 1st one is on channel 1 and 2nd is on channel 5, I've set RC5_FUNC as Flap_auto and everything is working good on…
Feb 5, 2014