About

Gender

Male


Location

Peshawar


Please tell us a bit about your UAV interest

Interested in multi-rotor platforms and RPi.


Activity Feed

Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"@iyad You adjust DNRate parameter on the transmitter to get a corresponding PWM value on the mission planner. 0745 was my DNRate parameter value on the transmitter whereas 1165 is the PWM value on the mission planner."
Feb 7, 2015
Majid Khan left a comment for Majid Khan
"Sorry. I couldn't get you. Are you talking about a hex rotor or HEX is a transmitter brand like Turnigy?"
Jun 27, 2013
Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"Just flip the switch to auto, provided to got a programmed autonomous mission uploaded to APM and auto on a switch."
Apr 6, 2013
Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"@Silviu
On your turnigy 9x controller, Press menu, then press DN to select FUNC Settings, enter it by pressing menu again.
Go to Prog.Mix and there you can find different channel mixes.
Kindly go through the blog again. I hope you will figure this o…"
Mar 18, 2013
Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"@Steve Burton
Sorry for late reply.

Please check the connections. Make sure pin 5 of receiver is not connected to APM. Also pin 6 of receiver is connected to APM pin 5, pin 7 of receiver to APM pin 6 and pin 8 of receiver to APM pin 7.

In order to…"
Mar 15, 2013
Majid Khan commented on CrashingDutchman's blog post Hobbyking sells ZeroUAV YS-X6 autopilot GPS flight control system
"And here it is available for 479 $.
Zero UAV YS-X4 multi-rotor FC WIFI Version"
Feb 18, 2013
Majid Khan commented on Marco Bauer's blog post PX4 Autopilot: BlinkM driver with system supervision
"Can this be integrated with APM? I mean to say that how would one get the status of different sensors for APM? Can your code be modified for APM?"
Feb 18, 2013
Majid Khan replied to Muhammad Rizwan's discussion Programming the MPU6000 in APM2.5 in Learning to program the Ardupilot Mega
"I think you are missing with the arducopter libraries in your arduino environment."
Feb 11, 2013
Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"Sorry. I haven't included a diagram but i have shown the connections in the post. The receiver is connected by connecting the receiver channels to the APM input. The receiver will be powered by using PWR and GND available from the APM.

First line i…"
Jan 11, 2013
Majid Khan commented on Majid Khan's blog post Configuring Turnigy 9x with arducopter
"Yes Simone Chiaretta. You are right. You have to reverse the pitch stick. I forgot that. Thanks for the addition."
Jan 7, 2013
Majid Khan posted a blog post
ManualThere had been two blogs regarding configuration of Turnigy 9x with APM but i had experienced difficulties in them. So here i am, writing my own experience.I am using the Turnigy 9x Mode 2 with RF 9X v2 2.4GHz module and 8 channel receiver but…
Jan 4, 2013
Majid Khan commented on Max Levine's blog post ArduPilot/Copter Mega 6 position 'mode' switch for FlySky/Tunigy 9x/ and others.
"Why use an analog dial or CLI for checking the PWM pulse widths when the feature is already available in Mission Planner. Just go to configuration and then flight modes and you can see the current PWM. change the value on your transmitter and you ca…"
Jan 4, 2013
Majid Khan replied to Christopher Cooper's discussion Channel 6 problems
"By the way i need help regarding the modes setup. What is the best configuration that you tried? If i have to use six modes, is it necessary to lose one channel i.e. Channel 6. Can't i set up the modes with channel 5 and channel 8?"
Jan 4, 2013
Majid Khan replied to Christopher Cooper's discussion Channel 6 problems
"Did you disable the mixing in the prog.mix in the menu? Go to each mixer that you tried to change for mixing (or all so that there is no doubt) and set the state of each mixer to INH i.e. In active. I think this might solve your problem."
Jan 4, 2013
Majid Khan posted a discussion
How does complex geo fencing works for arducopter? From where to configure it? I am trying but the geo fence appears shaded (disabled) in right click menu in flight planner tab in Mission planner?
Jan 3, 2013
Majid Khan commented on Manfred Dickgiesser's blog post T-Rex 600E Pro setup
"I am currently working on a quad and hex rotor. But endurance is the problem. What will be i losing if i switch to heli? How much endurance can i expect?"
Jan 2, 2013
More…