About

Gender

Male


Location

Shah Alam


About Me:

amateur APM


Please tell us a bit about your UAV interest

multirotor system microcontroller


Hometown:

Malaysia


Activity Feed

Mohd Hanif Mohd Ramli replied to Jiro Hattori's discussion Flying Arducopter in Japan in Japan ArduCopter Group
"Hattori san, 
Thank you very much, i have browsed to the the mentioned website. It is great to know that the company has wide range of choice for RC Hobbyist. 
I will pay a visit in this weekend. "
Feb 26, 2014
Mohd Hanif Mohd Ramli replied to Jiro Hattori's discussion Flying Arducopter in Japan in Japan ArduCopter Group
"Thank you very much Randy.
Nice to meet you too.
Yes i do agree with you, safety first. It is not right to fly around without considering the failsafe. I have tuned the failsafe last week, and performed flight testing at the nearby football field…"
Feb 25, 2014
Mohd Hanif Mohd Ramli replied to Jiro Hattori's discussion Flying Arducopter in Japan in Japan ArduCopter Group
"I am currently using the following setup;
1-TBS Discovery Frame kit with APM 2.6
2-FPV gear, Fatshark Predator V2 Vision System
3-Bullet Proof ESC, 900kv Tiger Motors, Graupner 9X5 Propellers
4-4500Mah 4S battery 
5-Turnigy 9XR with Frsky Module…"
Feb 25, 2014
Mohd Hanif Mohd Ramli replied to Jiro Hattori's discussion Flying Arducopter in Japan in Japan ArduCopter Group
"Thank you very much Mr. Hattori for the warm welcome and supportive information. I will comply the rules and regulations as stated. Since there is a specific radio transmitter could be used in Japan, i would like to know whether 2.4Ghz frequency is…"
Feb 25, 2014
Mohd Hanif Mohd Ramli left a comment on Japan ArduCopter Group
"Hello everyone, i am from diy drones Malaysia, have been active with multirotors since 2011..from APM1.4 oilpan to 2.6. Now i have moved to japan for job attachment for 3.5 years. I have some questions regarding flying multirotors in japan, what are…"
Feb 25, 2014
Mohd Hanif Mohd Ramli left a comment on DIY DRONES MALAYSIA
"Sihat..selamat datang ke DIY DRONES MAS.."
Feb 21, 2013
Mohd Hanif Mohd Ramli left a comment for Mohd Hanif Mohd Ramli
"Ooo..sory took me  so long to attach u this param. I agree that during the landing sequence it bounce a lot and i have managed to reduce it as i recalibrate the compass via live calibration. and setup RTL landing to 0.0m. i was busy config the…"
Oct 21, 2012
Mohd Hanif Mohd Ramli left a comment for Owen Booth
"Hello Owen,
This is my setup for AC2.7.3
RTL was nice 
AC2.7.3_waypoint_kajang_23092012.param"
Oct 21, 2012
Mohd Hanif Mohd Ramli left a comment for Owen Booth
"Thanks for ur suggestion, i will add it up soon..Today, i tested waypoints..finally i managed to do waypoints with RTL..for RTL, it worked very well and landed nicely, i set alt (abs) at 5m and did live calibration before take off. i can email u the…"
Sep 23, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"@Owen. yea, i agree..to overcome the issue i use ubloc gps, and it has additional battery on the module,within 20-30 seconds it lock the sats,usually 7sats..never reach 12sats so far..if u dont mind,could u share how can i connect additional ubec to…"
Sep 21, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"@Owen. Nice video man..i wonder why do u use ubec to power up APM?i never use it, just feed in using esc.."
Sep 21, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"@Owen. I have not tested RTL yet but looking forward to. for now i am putting efforts to test for auto landing and way points..if u dont mind,u you share a bit your experience in testing RTL..Thanks bro"
Sep 20, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"@Owen..as long as it work, i'm happy with it..thanks anyway..any idea where i could find out on how to set way points?i'm using APM 2.5 with 915Mhz radio telemetry. not sure how it goes.."
Sep 19, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"@Owen. Thanks bro..i have managed to make it work..what i did was feed in +12v to minimOSD during firmware and char update..but now i have new issue, i need to reset everytime using it..if not, it only show up this..update char set"
Sep 19, 2012
Mohd Hanif Mohd Ramli commented on Grips's blog post MinimOSD Setup Video
"Hi, a little help here.. i have followed all necessary steps, (using on 5V to feed into MinimOSD) but i coud not see the overlay char, it only showed up booting then with this message...update char...i have updated firmware and char many times, but…"
Sep 19, 2012