Gender
Male
About
Location
Melbourne
About Me:
Open source advocate. Strategic Planning Manager at APRIL - FibreOne (Technical Services, Strategic Planning Department) Riau, Sumatra, Indonesia at the moment.
Please tell us a bit about your UAV interest
Customising open source UAV hardware and software for aerial photography for natural resource management (e.g. forestry plantation, agriculture, mining,etc.) as well for mapping application for natural calamities (typhoon, earthquakes, etc.)
Hometown:
Melbourne, Australia
Activity Feed
"Nice.
It supports Ardupilot ChibiOS firmware connect, flash and configure settings in MacOS now.
It works well MacOS Sierra.
Thanks."
It supports Ardupilot ChibiOS firmware connect, flash and configure settings in MacOS now.
It works well MacOS Sierra.
Thanks."
"I have difficulties using the previous firmware (i.e. Arducopter 3.4.6). Pixhawk 1 is kaput (not working) at the moment. Inform us if you managed to revert to previous version firmware using MP. Carlos Jorge Martins Vicente said:
Well apart from…"
Well apart from…"
"Arducopter 3.5.3 for Pixhawk 1 is unusable. I got the same problem using Arducopter 3.5.3 in Pixhawk 1 ver. 2.4.7. This might be attributed to this bug. https://github.com/ArduPilot/ardupilot/issues/6969 PX4IO not working."
"@Patrick, I am interested of FlirOne with Rasberry Pi 3 for Aerial Thermal Photo Mapping. Can the FlirOne be trigger with USB cable? Or this is doable with Rasberry Pi Linux? The idea is to trigger FLirOne using USB cable attached to Pixhawk FC. The…"
"@Bill. I emailed you already. Thanks."
"@Bill. OK. I will email you and will pay using PayPal. Thanks."
"@Bill, you have SEEK Thermal camera trigger for Pixhawk? Does it means that you interface this SEEK thermal camera using MAVROS or Mavlink and use the telemery port of Pixhawk? I am very interested to buy a camera from you if I could geotagged the…"
"What flight controllers working on k501g? Is Pixhawk1 working on k501g?"
"How much is this unit - k501g? Less than USD 300 per unit?"
"What is your FC - Pixhawk1?"
"I would be good to see some documentation on which firmware to download and flash SOLO firmware with the new firmware that support the new Drotek RTK. I like see Wiki or documentation how to install a new firmware from Drokek (if possible) for SOLO…"
"Eagerly waiting to see, full integration of Pixhawk2.1 in 3DR Solo. Hope to see soon "3D Solo firmware + PH2.1" (i.e. ArduCopter 3.4 for 3DR Solo + Pixhawk2.1) works in 3DR Solo and "ProfCNC RTK GPS" as well."
"Ben
Can you email me, nsicad@gmail.com so I can buy this unit from you.
Thanks, Noli"
Can you email me, nsicad@gmail.com so I can buy this unit from you.
Thanks, Noli"
"Hi Ben,
I am interested to buy this - PIKSI GPS SYSTEM?
Where are you located in Australia?
I am in Melbourne.
Noli"
I am interested to buy this - PIKSI GPS SYSTEM?
Where are you located in Australia?
I am in Melbourne.
Noli"
"Hi Rone,
I think this device does not working with 3DR Solo since it does NOT have RDF telemetry (e.g. 433Mhz and 915Mhz as shown your the photos of the 2 RDF antenna).
3DR SOLO works on WiFi (2.4 Mhz frequency)."
I think this device does not working with 3DR Solo since it does NOT have RDF telemetry (e.g. 433Mhz and 915Mhz as shown your the photos of the 2 RDF antenna).
3DR SOLO works on WiFi (2.4 Mhz frequency)."
