Gender
Male
About
Location
Barcelona
About Me:
Spanish student interested in robotics and currently building an Arducopter Quad as a long term project.
Please tell us a bit about your UAV interest
I've always loved flying devices and robotics, so put it together and htere you have UAVs
Hometown:
Sabadell, Barcelona
Activity Feed
"Respecto al primer problema no te puedo ayudar, pero lo del GPS me paso a mí tambien.
Dentro de casa el mío no recivía señal, pero fuera funcionaba perfectamente. Pruebalo con un portatil en un parque sin edificios alrededor y te debería funcionar."
Dentro de casa el mío no recivía señal, pero fuera funcionaba perfectamente. Pruebalo con un portatil en un parque sin edificios alrededor y te debería funcionar."
"Hola,
No se mucho sobre la programación ni algunas cosas que comentas, pero sí que puedes conectar el receptor a un portatil usando una capturadora. Ten en cuenta que a menos que la capturadora sea muy buena tendras un ciertp lag de 1 o 2 segundos,…"
No se mucho sobre la programación ni algunas cosas que comentas, pero sí que puedes conectar el receptor a un portatil usando una capturadora. Ten en cuenta que a menos que la capturadora sea muy buena tendras un ciertp lag de 1 o 2 segundos,…"
Hi, my name is Óscar and I'm working on a drone project.I built my drone, test it several times and it flies OK. However, I just acquired a laptop and installed APM Planner 2 and can't get my APM board to connect to it since the APM Planner 2 won't…
"The wire is soldered, however, I can spot a power loss in the motor as it flies unstabilized just after doing the accrlerometer calibration.
Also, during the test flight, there was a front left motor failure, so the quad flipped (at 1m altitude)…"
Also, during the test flight, there was a front left motor failure, so the quad flipped (at 1m altitude)…"
"I soldered the cable but I want your opinion before I put the shrinking tube on the solder.
Is this soldering OK (I'm not the best one at this, but I think it'll do the job).IMG_20140918_163504.jpgIMG_20140918_163454.jpg"
Is this soldering OK (I'm not the best one at this, but I think it'll do the job).IMG_20140918_163504.jpgIMG_20140918_163454.jpg"
"Ok, I'll try doing this. I'll tell you if it worked."
"Wow, I didn't know anything about that. One thing, could you explain me the process of twisting the cables together please?
I'm Spanish and I don't know English perfectly ^^"
I'm Spanish and I don't know English perfectly ^^"
"Yeah, that's it. i'll have to go buy some of it and shrinking tube."
"Thanks, one question, how do you call that liquid that you use to presolder the wires?"
"I add a photo of the cable status right now.IMG_20140917_162911.jpg"
Hello,My problem is the following: I had an unfortunate crash and one of the cables of a motor (the red cable, which I suppose that is the power cable) broke. The rest of my quadcopter is fine, I tested everything and it works.Due to living in…
"Ok, I'll check that. Thanks for the info."
"It is in heli mode, why shouldn't it be, I use a multicopter, which is a lot similar to a heli."
"Thanks, I'll try that tomorrow."
"Still, I don't understand why. I didn't change any setting. I'll check all settings but, do you know by chance any way to reset all settings to fabric on the Turnigy 9x?
Thanks for the information and help, I really appreciate it."
Thanks for the information and help, I really appreciate it."
Hello,After long hours of Google searching and digging in this forum, I couldn't find any information about this (maybe it is just that I don't know how to search).The issue is that for some reason, my Channel 5 pulse changes according to my…
