Gender
Male
About
Location
Capital,Buenos Aires
Activity Feed
"Jani, that is really cool, i was thinking something really similar with an extra row for pins and jumpers in my version 2 in order to wire RX PIN to do ISP without disconnecting the boards when new firmware was available for any of them."
"I have created a 1:3 Fanout adapter that is working great with Telemetry + OSD + IOBoard and APM 2.5.
I have done it cutting a Stripboard of 4x5 holes and soldering 4 rows of 5 pins from a pin strip. Then i Interconected the rows as shown in the…"
I have done it cutting a Stripboard of 4x5 holes and soldering 4 rows of 5 pins from a pin strip. Then i Interconected the rows as shown in the…"
I wanted to share the integration i have done in my jdrones Quad.On the dome i have the Mediatek GPS.On the first deck, the FrSky Receiver, 1.2 Ghz Video Transmiter and Xbee TelemetryOn the second deck, MinimOSD, APM 2.5 and jD-IOBoard. The setup…
"Jani, any update about this development?
Patricio"
Patricio"
"Jani, Congrats on your new office!"
"My Updated setup for Arducopter and Base station"
"Cool, let me know as you get the new batch as i would like to order one, as a ESCs in my quad has failed so i would like to take advantage of that to do all the motoro soldering soldering once."
"Jani, i have done a adapter with a 5x3 Connector Header male and a 5x1 Header Female solered back to back and sealed with heatshrink.
When you connect the Telemetry, OSD and IOBoard, do you connect the 5 cables in all of them? Or you connect TX just…"
When you connect the Telemetry, OSD and IOBoard, do you connect the 5 cables in all of them? Or you connect TX just…"
"Jani, when are you starting to sell this board?"
"I have a Turnigy 9x + Frsky TX/RX with Telemetry + Smartie Parts addon for loading er9x + LiPo Bateries.
The setup is rock solid i am extremelly happy. The total cost of the setup is about $200
Hobbyking
1
Turnigy 9X 9Ch Transmitter w/…"
The setup is rock solid i am extremelly happy. The total cost of the setup is about $200
Hobbyking
1
Turnigy 9X 9Ch Transmitter w/…"
"Jani, i already have Xbee and jd-miniosd. Do you thing that the telemetry port would support a 1:3 fanout to add this board?.
Is there any issue to have this in parallel with the Xbee adapter?
Thanks
"
Is there any issue to have this in parallel with the Xbee adapter?
Thanks
"
Does Anybody know if there would be a respin of the APM2 daughteboard in order to include a three pin connector or some other easy access to the SPI pins without soldering the cables for the optical flow connector?I am ready to order APM2 however…
"Jerome, i am in the same situation than you. No video output on the minimOSD. I got this unit from jdrones but have been unable to get support from them.
Did you Have any luck on resolving this?
"
Did you Have any luck on resolving this?
"
"I had a crash last week testing 2.5.3 with a similar behaivior that some people reported. Quad leaning to its back.
an initial take of was attempted at 40-45% and i could land it. on the 55-59% i had the crash where i broke one propeller and end of…"
an initial take of was attempted at 40-45% and i could land it. on the 55-59% i had the crash where i broke one propeller and end of…"
I am trying to get HIL working with AeroSIM-RC, i am using the the RC radio to control this. I have done the radio calibration however i am hving a problem with the gain as it seems to be biased. When i use a big gain (10000) the copter doesnt take…
"Michael, thanks a lot for your response"
