About Me:
..
About
Please tell us a bit about your UAV interest
..
Activity Feed
"I have two CC ESC'S (Phoenix ice 75A and Phoenix Edge Light 100A) and never had a problem. I don't know if you know but CC release theirs protocol specifications: the Castle Link Live. You can find more info here. Also there is a very good…"
"Hello David,
You need to have the data stream rates configured correctly. To do so, connect to Mission Planner. Go to configuration. Locate EEPROM parameters and verify that you have the following parameters configured as here:
SR0_EXT_STAT,2…"
You need to have the data stream rates configured correctly. To do so, connect to Mission Planner. Go to configuration. Locate EEPROM parameters and verify that you have the following parameters configured as here:
SR0_EXT_STAT,2…"
"Hello,
You can download the new firmware (still pre-release) and the new configuration tool here. This includes a small modification of Call Sign panel (now all letters are lower case) and also a new option to control characters brightness.
Enjoy…"
You can download the new firmware (still pre-release) and the new configuration tool here. This includes a small modification of Call Sign panel (now all letters are lower case) and also a new option to control characters brightness.
Enjoy…"
"Hello,
The new Call Sign is ready! You can download the new firmware (still pre-release) and the new configuration tool here.
Enjoy and please give feedback!
Pedro"
The new Call Sign is ready! You can download the new firmware (still pre-release) and the new configuration tool here.
Enjoy and please give feedback!
Pedro"
"Hello Andrew,
Thank you very much for you quick support!
I was looking in the function "send_extended_status1" and found this:
uint16_t battery_current = -1; uint8_t battery_remaining = -1;
Two negative values in unsigned integers. Is this…"
Thank you very much for you quick support!
I was looking in the function "send_extended_status1" and found this:
uint16_t battery_current = -1; uint8_t battery_remaining = -1;
Two negative values in unsigned integers. Is this…"
"Hello to everyone,
A new stable release of MinimOSD Extra firmware (V2.1) is now in downloads area. There are many changes since the last stable. Among them are the support for two independent panels that can be switched using the mode channel,…"
A new stable release of MinimOSD Extra firmware (V2.1) is now in downloads area. There are many changes since the last stable. Among them are the support for two independent panels that can be switched using the mode channel,…"
"Hello to everyone!
We have just released an new version of the firmware and Configuration Tool. The main news are the added CH 5 for screen change as possible selection. We have also added the function Andke have requested (rotation switching by a…"
We have just released an new version of the firmware and Configuration Tool. The main news are the added CH 5 for screen change as possible selection. We have also added the function Andke have requested (rotation switching by a…"
"Hello to everyone,
Gábor brought to my attention that, in the configuration tool, was impossible to set CH 5 to Toggle switch. I've corrected this small bug. You will find a new download with this corrected in MinimOSD extra project page.
Pedro "
Gábor brought to my attention that, in the configuration tool, was impossible to set CH 5 to Toggle switch. I've corrected this small bug. You will find a new download with this corrected in MinimOSD extra project page.
Pedro "
"Thank you.
What about my other question: Is the I2C port connected to the 3.3V side of the voltage translator as in APM2.0? Thank you again!
Pedro"
What about my other question: Is the I2C port connected to the 3.3V side of the voltage translator as in APM2.0? Thank you again!
Pedro"
"Hello,
When will be available the new schematic and board files of APM 2.5? Is the I2C port connected to the 3.3V side of the voltage translator as in APM2.0? Thank you in advance.
Pedro"
When will be available the new schematic and board files of APM 2.5? Is the I2C port connected to the 3.3V side of the voltage translator as in APM2.0? Thank you in advance.
Pedro"
"Hello,
You can download the eagle board file here, which contains all the dimensions.
Pedro"
You can download the eagle board file here, which contains all the dimensions.
Pedro"
"Hello,
I've written a lot of code portions to expand ArduPlane to a particular project that I'm involved, mainly to add rpm sensors and temperature sensors. I also have added more Mavlink messages to send the additional data to QGroundcontrol.…"
I've written a lot of code portions to expand ArduPlane to a particular project that I'm involved, mainly to add rpm sensors and temperature sensors. I also have added more Mavlink messages to send the additional data to QGroundcontrol.…"
"Hello,
Have a look here.
Pedro"
Have a look here.
Pedro"
Hello,Is there a pin mapping of APM2, similar to the one available to APM1 (link: http://code.google.com/p/ardupilot-mega/wiki/Hardware)? Thank you in advance.Pedro Santos
"Hello,
You can find the schematic and board layout in the diydrones store (link below).
Pedro
https://store.diydrones.com/APM_2_0_Kit_p/br-ardupilotmega-03.htm
"
You can find the schematic and board layout in the diydrones store (link below).
Pedro
https://store.diydrones.com/APM_2_0_Kit_p/br-ardupilotmega-03.htm
"
"Any news on MavLink 1.0 implementation? Thank you.
Pedro Santos"
Pedro Santos"
