About

Gender

Male


Location

New South Wales


About Me:

Electronics technician with over 40 years experience. Like to travel. Enjoy life to the most of my ability.


Please tell us a bit about your UAV interest

Currently have a bixler 2 with storm osd. Have just made a gimbal for this plane to carry a Mobius camera. Sofar so good. Have Skywalker all but ready to fly. It has OSD5 onboard. Just getting in to quad / tricopter with an APM board to control flight.


Hometown:

Yamba


Activity Feed

Phelec replied to Alfie's discussion New mission planner compass calibration
"Aha, that did it. Thanks......."
Apr 22, 2014
Phelec replied to Alfie's discussion New mission planner compass calibration
"I cannot see any "Advanced Menu" selection. Unless it is hidden with the Terminal selection..LOL.
Right clicking on the top tool bar just opens 2 options to select:
Auto Hide    and   Full Screen"
Apr 22, 2014
Phelec replied to Alfie's discussion New mission planner compass calibration
"I apologise if this is a bit off topic.
My mission planner just updated to version 1.3.0.
Now, I do not have a "Terminal" icon in the upper tool bar area.
I am new to MP and the whole APM thing (getting up to speed quickly though).
Am I just not…"
Apr 22, 2014
Phelec replied to Randy's discussion AC3.1 & blown 3.3V regulator (was AC3.1-rc5 SPI speed problem)
"Yes, I had a look earlier today. The addition of some extra caps is a good idea. Too many manufacturers like to save 5cents by leaving out those parts. As you said, the board will mostly work alright for 98% of the time, but when there is a sudden…"
Mar 28, 2014
Phelec replied to Randy's discussion AC3.1 & blown 3.3V regulator (was AC3.1-rc5 SPI speed problem)
"Good luck, you have solved your problem. The LD1117av33 is an overkill (very large). But, if you can mount it so any vibration will not fracture the solder joints, then I suppose it is OK.
Just be careful the weight of the LD1117av33 is large and…"
Mar 28, 2014
Phelec replied to Randy's discussion AC3.1 & blown 3.3V regulator (was AC3.1-rc5 SPI speed problem)
"Yes, I tried it with and without the compass/gps plugged in. Both ways it still would not complete the connection to Mavlink.
I have only had this unit for 10 days and that is also the amount of time I have been learning so far. I have been reading…"
Mar 28, 2014
Phelec replied to Randy's discussion AC3.1 & blown 3.3V regulator (was AC3.1-rc5 SPI speed problem)
"Thankyou Paul. (actually my name is Paul as well). Yes my board is a clone. It has 2.5.2 marked on the bottom and has the compass chip removed. I tried with and without an external compass/gps connected. I still somehow cannot except the CLI …"
Mar 28, 2014
Phelec replied to circuitburner's discussion new APM 2.5 setup problem
"Thanks Duncan. I tried in my haste this morning to reply to you before I had to rush off to work. However I did not press the correct buttons on the keyboard. I did not have time to retype everything.
I am on the east coast of Australia. My 3.3 volt…"
Mar 27, 2014
Phelec replied to Randy's discussion AC3.1 & blown 3.3V regulator (was AC3.1-rc5 SPI speed problem)
"I received my APM2.5.2 clone last week. I have not fitted it to any copter so far. I have been getting familiar with MP and the APM board in general. So far I have only connected a USB lead (and the external compass/gps) to the board. There is no…"
Mar 26, 2014
Phelec replied to circuitburner's discussion new APM 2.5 setup problem
"I think I am in this same boat. It is a shame when someone starts a thread and then leaves it cold..."
Mar 26, 2014