About

Gender

Male


Location

Ballarat


About Me:

I am an Aircraft Engineer and RA-Pilot, though now I mainly do electronic design Kids, wife, the normal stuff....


Please tell us a bit about your UAV interest

Developing a new flying platform,


Hometown:

Ballarat


Activity Feed

Philip replied to UAV Skies's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in PIXHAWK
"EDIT: 27th of April 2019: Ardupilot has now added detection, prearm checking, and inflight checking and failover to the redundant sensors. This is now in Release Copter and Release Plane.

Detection of the fault has also been added to Mission…"
Apr 27, 2019
Philip replied to UAV Skies's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in PIXHAWK
"Thankyou very much "
Apr 25, 2019
Philip left a comment for Philip
"I don’t visit DIYDRONES much anymore, discuss.cubepilot.org is where I’m at"
Apr 24, 2019
Philip replied to UAV Skies's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in PIXHAWK
"Thanks, but I would still suggest making it just the link.
in a year from now, will you still be wanting to manually edit this if more information comes to light? "
Apr 24, 2019
Philip replied to UAV Skies's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in PIXHAWK
"All 2019 cubes are grounded till further notice. "
Apr 24, 2019
Philip replied to UAV Skies's discussion SB_0000002 Critical service bulletin for Cubes Purchased between January 2019 to present. DO NOT FLY in PIXHAWK
"You have posted out of date information.

please only post the link to the correct information. "
Apr 24, 2019
Philip commented on Gary Mortimer's blog post uAvionix, ProfiCNC, and HEX announce ADS-B IN capability for The Cube Autopilot
"Thanks Gary!"
Apr 18, 2019
Philip replied to Sohaib Ahmed's discussion Pixhawk 2.1 Hardware Limitations in Pixhawk 2 User Group
"The cube has flown much faster than that, and can handle +/- 16 G"
Mar 26, 2019
Philip replied to Ken Wilkins's discussion Need advice on equipment in Pixhawk 2 User Group
"The barometer will give you that data. Ensure you have GPS for the timing... the gps will also give you that data."
Aug 21, 2018
Philip replied to Timothy's discussion Pixhawk 2.1 Throttle Calibration not working - motors wont spin need help! in Pixhawk 2 User Group
"Support for Ardupilot or The cube is given at either the cube Facebook page or the Ardupilot “discuss . Ardupilot . Org”"
May 9, 2018
Philip replied to Robert Baumgartner's discussion Pixhawk 2 - board damaged (maybe) from factory in Pixhawk 2 User Group
"This exact same post is on so many sites, it’s difficult to answer them all.

If your board is broken, RMA it via your local distributor

The glue is added to increase support for this connector as so many people are forgetting to use the clip.

For…"
Apr 13, 2018
Philip replied to Ken McNamara's discussion What is the difference between Pixhawk 2 and Pixhawk 2.1? in Pixhawk 2 User Group
"Support for the cube (Pixhawk 2.1) is on discuss.ardupilot.org
Or Facebook
https://m.facebook.com/groups/847946361954654

Thanks
Phil"
Jan 3, 2018
Philip left a comment on 3DR SOLO
"best place for Solo questions is the solo group on Facebook.we are actively supporting solo, and continuing to build on this awesome platform.https://www.facebook.com/groups/3DRSOLO/"
Apr 3, 2017
Philip replied to Randy's discussion Optical Flow discussion thread
"Best ask this at discuss.ardupilot.org"
Apr 2, 2017
Philip replied to Sriram's discussion Pixhawk Stability in PIXHAWK
"first comment, why would you fly with 3.3? move to release, or 3.5RC2.  "
Mar 20, 2017
Philip replied to jeerasak moudpoklang's discussion how to get sensor data form pixhawk using mavlink? in PIXHAWK
"Or look up dronekit..."
Mar 7, 2017
More…