Hello,
Have a 3DR Y6 BNF for sale, get it as a kit bind & fly or cannibalize it - cheaper together in you can pickup in NYC area, or 'a la carte'. Sad but it must go! A lot of fun to build and fly, flies great - Here's a vid of it in action:
| Oahu, Ha |
Hello,
I'm helping someone install an analog airspeed sensor with the pixhawk, the wiki says:
The “airspeed” pin 15 is located on a 3 pin DF13 connector on the Pixhawk board.
This pin can take voltages up to 6.6V (it has an internal voltage divider).
The
Hi Everyone,
Very weird crash today. I have 12-15 flights all flawless before this incident. When it occurred I immediately thought I lost a servo - but upon inspection both servos were fine. Watching the video (below), I did not input the left roll
Hi Everyone!
I've been tasked with shooting some video indoors. Through the 3.2 beta thread I remember there being a few mentions that GPS data is used when EKF is enabled even when not in GPS modes.
I would really appreciate some input, clarification
Read more…Hello,
specs:
APM 2.6 + external compass & GPS
3DR power module
Mission Planner 1.2.95 build 1.1.5150.11972
Plane 2.78b
I'm having a strange issue with my current sensor, hoping someone can help. When the plane is sitting idle, it is reporting 88 amps; her
Read more…Hello,
Weird problem - while the plane is on the bench, the hud is constantly moving. I have calibrated gyros multiple times and it still continues. what could be causing this?
Here's a video:
http://youtu.be/WvjNyfQC45o
APM 2.6 + gps/external compass
3
Hello,
I am new to APM:Plane and appreciate any help I can get. I was able to maiden my flying wing today with success in manual mode (woohoo!). A few subtrim/ trims were made on my remote to keep it flying straight.
When i tried to switch to stabilize
Read more…Hello,
I am on my first APM-plane build. I'm having a weird issue where on boot of the APM, one of my servos is pushed 100% in one direction. This only happens if the signal wire is plugged into the APM.
Here's a video: https://www.youtube.com/watch?v=
Read more…Hi All,
I've been building APM driven multirotors for a bit and this is my first try with an APM based plane, looking for a little help.
Due to the tight space on my frame, it would really help if i could mount the APM as pictured below:
After research
Read more…Hi all - recently build a quad and have been testing it the last few days.
Yesterday when I came to land I noticed the copter was leaning forward a lot - so much I had to pull back the stick to level and land nicely (otherwise it would of crashed on i
Read more…Hi all,
I was flying around and experienced a radio failsafe. RTL was engaged for one second and seemed like all motors were cut off while in RTL. Failsafe went away & stabilize kicked in very quickly, but my full throttle was not enough to recover -
Read more…Last week I received 4S batteries and have been trying to tune the PID's on my Y6 for it. I am hoping some of you who are using 4S batteries can share your params so I can compare. I started with the params file posted on the 3DR site. http://3drobot
Read more…Last week I received 4S batteries and have been trying to tune the PID's on my Y6 for it. I am hoping some of you who are using 4S batteries can share your params so I can compare. I started with the params file posted on the 3DR site.
I'm having a ha
Read more…Hello,
I ran across this thread over at google code drones discussion and would like to bring attention to it, hoping 3DR chimes in and can clarify if indeed the rear blades need to be swapped (and documentation updated to reflect this). You will noti
Read more…Hello,
I'm curious how many people are using 4S batteries with their Y6 and how it performs. I was planning on trying a couple 4S batteries, but whenever I do any calculations on ecalc with a 4S battery, it says over power (260w vs 200w rating for the
Read more…Hello,
I'm trying to avoid an issue with the 5v regulator on the analog side (12v input) . It drastically decreases my UHF radio range by creating noise in the same freq (433 MHz)
From the wiki, i see this option to connect the analog/digital sides so
Read more…Hello,
I am searching for high quality 30a simonk flashed ESCs that can handle up to 4S. I can't seem to find information on which are good & reliable ESCs, and really don't want to buy subpar hardware that is prone to failure - I am hoping the cummu
Read more…Hello,
I'm very curious if there are any mechanical differences between the old 3DR 850kv motors (with the bullet prop adapters) vs the new 850kv's with the new style prop adapter. I'm worried about mixing the two motor types, which seems like a very
Read more…Finally decided to play around with auto mode and waypoints today. If i take off manually, then switch to auto mode when it is in the air, my Y6 perfectly goes from waypoint to waypoint, lands etc..
Unfortunately, anytime i try to auto take off, as so
Read more…Hello,
I'm having a weird issue, hopefully someone can help! I am running MinimOSD 2.2 extra copter.
before arming, all OSD values are updated properly. However, as soon as ARM, 2 seconds later everything freezes (values do not change). This only happe
Read more…