About
Activity Feed
"Hi Justin!
Do u have some positive results with your wind-resistand code testing? "
Do u have some positive results with your wind-resistand code testing? "
"Hello Toby,
it realy cool, but Ive some questions.
Did u check a time delay of command execution? Its suspiciouce short. From video it looks like less half second.
Are u sure that there are no any direct connections between APM and Ground station…"
it realy cool, but Ive some questions.
Did u check a time delay of command execution? Its suspiciouce short. From video it looks like less half second.
Are u sure that there are no any direct connections between APM and Ground station…"
"Hello Anant,
Is it releability for dust and snow? I mean UG01.
Didnt u think about Kinect using? It has the same stucture and more chipper.
http://www.iheartrobotics.com/2010/12/limitations-of-kinect.html"
Is it releability for dust and snow? I mean UG01.
Didnt u think about Kinect using? It has the same stucture and more chipper.
http://www.iheartrobotics.com/2010/12/limitations-of-kinect.html"
Hello people, is it possible to use a Kinect for land mapping and improve quality of autolanding? All advice are welcome
"Hello,
has anyone ideas how to integrate it with AP or APM?"
has anyone ideas how to integrate it with AP or APM?"
Yello People! Ive a ArduIMU board v2. It worked well till now.At present I have the same problem as discribed here:http://diydrones.com/forum/topics/problem-in-firmware-uploadingi.e. if i try to upload a code it hasn't finished well - it "Updating…
Yello People!What you suggest is it possible to make a weight reduce for stroke engine by change engine parts?I mean parts from another more light material.What do you think? Any experiences? For exaple for those…
"PS examples for NewSoftSerial compiles without any problems..."
Yello,I've tried to use a NewSoftSeial library (from here http://arduiniana.org/libraries/newsoftserial/) for communication to addition device.Then I changed a source code I have a strange…
"Yello Paul,
did you change a AP code?
Could you share your's changes wiht explanation"
did you change a AP code?
Could you share your's changes wiht explanation"
"Yello,
if I want to test simulation AP without transmitter in AUTO mode only do I need to change this your's code and hardware?
As I see it doesnt need. I think that code changes will be anought.
Is your changes needs for MANUAL and FBW modes only?"
if I want to test simulation AP without transmitter in AUTO mode only do I need to change this your's code and hardware?
As I see it doesnt need. I think that code changes will be anought.
Is your changes needs for MANUAL and FBW modes only?"
Yello people,Im trying to use a AP 2.7.1 and Ardupilot2Sim v0.44 to complete AUTO simulation.And then I try to do that I have a problem by takeoff phase.I found a solution for previouse version AP 2.7. There was the same problem. And the cure was…
Yellow people!I've a question about PID.Is there some situation than I need to tune a PID parameters (AP_PID_settings.h)?How to calculate it and where from depends (I mean airframe size, mass, and so one)
"Yello RolandS888,
tell me please - what kind of autopilot did you use? AP, APMega ar something else?"
tell me please - what kind of autopilot did you use? AP, APMega ar something else?"
"as I see there are following airframe depence paremeters:
Apconfig.h
/***************************************/
// AIRFRAME SETTINGS
#define MIXING_MODE 0 //Servo mixing mode 0 = Normal, 1 = Elevons (or v tail)
// NOTE - IF USING ELEVONS, 1-2 AND…"
Apconfig.h
/***************************************/
// AIRFRAME SETTINGS
#define MIXING_MODE 0 //Servo mixing mode 0 = Normal, 1 = Elevons (or v tail)
// NOTE - IF USING ELEVONS, 1-2 AND…"
