Gender
Male
About
Location
Pordenone
About Me:
I'm not developer , i know a little bit software, I like to build 3d with cad cam and cnc
Please tell us a bit about your UAV interest
Like open source arducopter project!
Hometown:
Italy
Activity Feed
"Someone know the exact order pin SDA SCL GND VCC on APM 2.5 to connect external mag please?port.jpg"
"the version 3.1work with apm 1 (Now not work xbee and alt hold)? and when it is release?"
"the release fly very well ! but i'm not capable to setup althold , every time to switch in this mode fall down until touch ground and stay about 10 cm and stay here , or lift up in the sky...
there is definitely a problem that I can not identify (…"
there is definitely a problem that I can not identify (…"
"Congratulation !Great release! very stable and fun !
but a a strange thing happens, every time motor start lost connection with pc ( i use xbee900)
and when stop it is regularly reconnected ?!?
up to version 3.0.0 rc6 work fine , how it change?"
but a a strange thing happens, every time motor start lost connection with pc ( i use xbee900)
and when stop it is regularly reconnected ?!?
up to version 3.0.0 rc6 work fine , how it change?"
"Hi ,
anyone can help me to understand why altitude hold not working properly?
on alt hold stay good for some time and sometime lift up ... sometime fall down
in loiter fall down ...
in the APM planner i can see the altitude change only about 1 or 2…"
anyone can help me to understand why altitude hold not working properly?
on alt hold stay good for some time and sometime lift up ... sometime fall down
in loiter fall down ...
in the APM planner i can see the altitude change only about 1 or 2…"
"Hello everyone, I switched to version 2.9.1b from 2.8 and I noticed a lot more power in the throttle. To keep hovering throttle stick is now about 40%, how can I set this? when i switch to loiter mode my hexa fall down until the throttle stick is in…"
"Hi! someone try this?
I have a problem with pan control.
when inizialize it take absolute position, for example if i have imu at 10degree nord corrispond at 1800ms at servo, so that turn at the always in the same directions
and where i can modify…"
I have a problem with pan control.
when inizialize it take absolute position, for example if i have imu at 10degree nord corrispond at 1800ms at servo, so that turn at the always in the same directions
and where i can modify…"
"Hi Marc,I try the arduimu test sw but my board respond only roll . my board do not work correct!"
"Hi , i try on arduimu v3 , it is all ok when compile (arduino 100) and upload but work only roll servo ,
Servo degree work ok , all data changhe when change the position of board but servo output PCH and YAW stay only -1
Only servo roll work…"
Servo degree work ok , all data changhe when change the position of board but servo output PCH and YAW stay only -1
Only servo roll work…"
"Shared photos and cad file to build it ,
http://diydrones.com/forum/topics/i-d-like-to-share-my-hexa-project...
parameter .... working progress :-)"
http://diydrones.com/forum/topics/i-d-like-to-share-my-hexa-project...
parameter .... working progress :-)"
"Hi everyone,I am a novice but I follow this discussion with interest from version 2.0.XX,
congratulations for the work.
I try every version from 2.0.48 to 2.3 on my hexa with apm1 ,
with this version i have a stab P Pitch and roll = 3 Stab I 0 Stab…"
congratulations for the work.
I try every version from 2.0.48 to 2.3 on my hexa with apm1 ,
with this version i have a stab P Pitch and roll = 3 Stab I 0 Stab…"
Attached file and photo for FatHexaif u like it build it!and...other design frame project herehttp://www.youtube.com/watch?feature=player_embedded&v=u1a5mgPPt4Yhexafull.jpgFatHexaIGS.rar
