About

Gender

Male


Location

Douglasville, GA


Please tell us a bit about your UAV interest

My UAV interest is fairly new. I am hoping to build on my limited knowledge of the field so that I can one day utilize UAV's for commercial purposes.


Hometown:

Douglasville, GA


Activity Feed

Serpentaire commented on Bruce Jones's blog post Getting 6 Modes out of Channel 5 on a Spektrum DX7s
"That's what I use Aux2 for as well. Unfortunately, I'm just not sure since Aux1 is used for mixing to get 6 flight modes. It might only be possible with the dx8 since it has an extra channel. You might experiment by replacing AX1 in the mixing menu…"
Oct 1, 2013
Serpentaire commented on AKRCGUY's blog post Wow! Check out this perspective....
"Ditto...very cool.  But I'm getting a fierce case of that iOS 7 vertigo watching these vids."
Sep 30, 2013
Serpentaire commented on Bruce Jones's blog post Getting 6 Modes out of Channel 5 on a Spektrum DX7s
"I'm really not sure about that.  I just built my setup off of the initial posting in this thread, which used AUX1.  AUX2 should be free for you to assign as you like.  You should be able to re-assign the switches as you see fit in the SW select area…"
Sep 30, 2013
Serpentaire commented on Wesley Versfeld's blog post Tarot T810 build log
"Jy het 'n wonderlike werk gedoen met hierdie bou

This is exactly the same type of build I'm planning to do in the near future.  Thanks for sharing.  Just a few questions though.  Are you running any other types of cameras on this bird?  Your gimbal…"
Sep 6, 2013
Serpentaire replied to John Kleiber's discussion Where are the PID settings for the Y6. The 3DRstore link is dead for the Hexa to Y6 Conversion Kit
"Aren't these setting automatically applied when you install latest Y6 firmware through Mission Planner? 
If not, how are these different? 

Also, how does one load these custom PID settings into their APM?"
Aug 26, 2013
Serpentaire commented on Wipo's blog post Y6 / X8 Thrust efficiency test
"Very interesting.  I just converted my hexa C to a Y6 last weekend.  Standard setup for the 3DR Y6 is 10' props on top and 11" on the bottom but they are spaced about 3-4 inches apart. 
I may need to do a bit more tuning but I've seen a slight…"
Aug 22, 2013
Serpentaire commented on Graham Dyer's blog post Testing a cheap(ish) brushless gimbal...
"Very stable video.  How do you fly the bird and control the gimbal at the same time?  Are the plans freely available for the pieces?  I guess, what I'm trying to ask is, do you have more details on how you construct/use this?  I've been looking for…"
Aug 14, 2013
Serpentaire left a comment for Roy Edmondson
"Hey Roy...."
Aug 14, 2013
Serpentaire left a comment for Rodney Meadows
"Are you building one yet? "
Aug 6, 2013
Serpentaire left a comment for Rodney Meadows
"Good luck with your aspirations Rodney.  I live in Douglasville as well.  Not much UAV centered activities going over here. "
Aug 6, 2013
Serpentaire replied to J A's discussion One motor/esc makes different beeps than the rest and spins more freely on throttle down
"I just recently noticed the same issue with my Hexa C as well.  I've manually/automatically calibrated the ESCs multiple times and they all seem to start up at the same time. 
However, I get a single higher pitched beep after plugging up LIPO.  I…"
Aug 5, 2013
Serpentaire commented on Bruce Jones's blog post Getting 6 Modes out of Channel 5 on a Spektrum DX7s
"Whoo hoo.....
Glad I could help Mitch. You are very welcome."
Aug 2, 2013
Serpentaire commented on Bruce Jones's blog post Getting 6 Modes out of Channel 5 on a Spektrum DX7s
"You mentioned the switch setting, did you mean the setup screen labeled SW Select? 

If so, this is what I have.

Trainer: Inh                   Flap: Aux1
F Mode: Inh                  Mix: Inh
    Gear: Gear               Knob: Aux2"
Aug 2, 2013
Serpentaire commented on Bruce Jones's blog post Getting 6 Modes out of Channel 5 on a Spektrum DX7s
"I took the settings that Bruce initially posted and tweaked them a bit and I was able to get all 6 flight modes functioning properly.
Not sure why I got it to work after so much tweaking but I cannot argue with the results.  Everyone is posting the…"
Aug 2, 2013
Serpentaire posted photos
Aug 2, 2013
Serpentaire left a comment for Deon van der Merwe
"Baie Geluk Merf....

Wonderful stuff and such great exposure.  I look forward to seeing the results of the study mentioned in the article. "
Aug 1, 2013
More…