Gender
Male
About
Please tell us a bit about your UAV interest
Uav
Hometown:
Attica
Activity Feed
"Dear All,
I own a DJI S900 with a Pixhawk controlling it and have done some land surveying missions with great success!
I recently mounted a Gremsy H6 gimbal and test flew it. I had a lot of vibration especially in the landing gear where you could…"
I own a DJI S900 with a Pixhawk controlling it and have done some land surveying missions with great success!
I recently mounted a Gremsy H6 gimbal and test flew it. I had a lot of vibration especially in the landing gear where you could…"
"Hi there,
Thanks for your reply. Have you tried this with Pixhawk and it worked?
I will use the jumper as I did not use it before. Should get 16 channels?
Thanks"
Thanks for your reply. Have you tried this with Pixhawk and it worked?
I will use the jumper as I did not use it before. Should get 16 channels?
Thanks"
"Ηι,
Have you connected a USB cable to the +3.3V output? If yes, which wires did you use please?
Thanks"
Have you connected a USB cable to the +3.3V output? If yes, which wires did you use please?
Thanks"
" Hi Luke. I saw your post regarding triggering a SX290 using the wonderful strattosnaper and took the liberty of contacting you, I am also trying to trigger the SX280 using the strattosnaper, but with no luck unfortunately. I have setup a two mode…"
"Hi again
Can I ask you this please? Which wires did you use from the modified USB cable that connects the strattosnaper to the Canon camera?
Cheers"
Can I ask you this please? Which wires did you use from the modified USB cable that connects the strattosnaper to the Canon camera?
Cheers"
"HI Hugues,
Thanks very much for your reply. The Canon accepts the standard mini USB connector, it should be ok you think?
In the strattosnaper software , do you set the push button configuration to trigger the shutter? Is this the correct function…"
Thanks very much for your reply. The Canon accepts the standard mini USB connector, it should be ok you think?
In the strattosnaper software , do you set the push button configuration to trigger the shutter? Is this the correct function…"
"Hi Hugues,
Bravo and thank you very much for your input. I have read this many times. One question, do you think I could trigger a Canon SX280 using the wire output from the strattosnaper and connect it to the USB port of the camera? Then all I…"
Bravo and thank you very much for your input. I have read this many times. One question, do you think I could trigger a Canon SX280 using the wire output from the strattosnaper and connect it to the USB port of the camera? Then all I…"
"Hello and thanks for the help.
I will try to take the schematic to a shop nearby and see if they can make it for me."
I will try to take the schematic to a shop nearby and see if they can make it for me."
"Hi there,
thanks very much for the input. So I guess that I connect the USB to servo cable directly on the strattosnaper, correst? Using two wirew only, ground and signal, yes?"
thanks very much for the input. So I guess that I connect the USB to servo cable directly on the strattosnaper, correst? Using two wirew only, ground and signal, yes?"
"Hi thre,
is it easy to configure? You just need to go to pixhawk camera gimbal menu, set the PWM values and then set these values as shutter range for triggering the camera's shutter? "
is it easy to configure? You just need to go to pixhawk camera gimbal menu, set the PWM values and then set these values as shutter range for triggering the camera's shutter? "
"SO the only route is to build one?
I really had hopes for the gentWire USB2! Anyone else guys that did have some luck with it?"
I really had hopes for the gentWire USB2! Anyone else guys that did have some luck with it?"
"Hi,
Thanks for the reply. You mean it is not sufficient to trigger the shutter . What else is needed with it?
Has anyone tested this using a strattosnapper?
Thanks"
Thanks for the reply. You mean it is not sufficient to trigger the shutter . What else is needed with it?
Has anyone tested this using a strattosnapper?
Thanks"
"Hi all,
Thanks very much for the useful info. I myself have been trying to setup the Canon HS280 to be triggered by the Pixhawk that has a BEC 5V connected to AUX rail, with no luck. Since I am very bad in building circuits, I would like to confirm…"
Thanks very much for the useful info. I myself have been trying to setup the Canon HS280 to be triggered by the Pixhawk that has a BEC 5V connected to AUX rail, with no luck. Since I am very bad in building circuits, I would like to confirm…"
"Hi and thanks very much for the reply.
Unfortunately I know almost nothing about RC systems and Futaba products, so I really do not know, I will google though to get an understanding.
Did you get all 14 channels? I mean if you connected something…"
Unfortunately I know almost nothing about RC systems and Futaba products, so I really do not know, I will google though to get an understanding.
Did you get all 14 channels? I mean if you connected something…"
"Hi there,
I am a Pixhwak user on a hexacopter and trying to get 14 channels out of the pixhwahk connected to a Futaba 6208Sb receiver. Has anyone achieved this sucesfully? Futaba manual says that you can set the receiver to mode B and get an extra…"
I am a Pixhwak user on a hexacopter and trying to get 14 channels out of the pixhwahk connected to a Futaba 6208Sb receiver. Has anyone achieved this sucesfully? Futaba manual says that you can set the receiver to mode B and get an extra…"
Hi there,I have a Futaba R6208SB connected to a pixhawk through SBUS and all work great.I would like to configure the 6208 for mode B usage, where I can get another 8 channels(9-16) through the analogue ports of the receiver. I do power the receiver…
