Gender
Male
About
Location
Marshall, MN
Please tell us a bit about your UAV interest
Pixhawk drone KK2 drone
Hometown:
Hometown
Activity Feed
Turnigy 2K action cameraI have used this camera for two months on my DIY 450 Quad.I like the quality of single shot photos and video.I have scratched the lens (did not use the protective case) but am happy to report that lens is replaceable as note…
"Dave,
I have flying quads for 3 years after 25 pleus years in RC airplanes. I started with a simple toy quad for $50 from amazon and got the expierence of safe flying.
Than I bought a 450 size quad installed KK2 control board and added a Turnigy…"
I have flying quads for 3 years after 25 pleus years in RC airplanes. I started with a simple toy quad for $50 from amazon and got the expierence of safe flying.
Than I bought a 450 size quad installed KK2 control board and added a Turnigy…"
"AntimatterCrusader
I setup my Spekturm 8 channel transmitter to HobbyKing OrangeRx 10 SBUS receiver with my Pixhawk without difficulty. I input the BND output on the OrangeRX into the RC input of the PIX.
Hope this helps.
Vince"
I setup my Spekturm 8 channel transmitter to HobbyKing OrangeRx 10 SBUS receiver with my Pixhawk without difficulty. I input the BND output on the OrangeRX into the RC input of the PIX.
Hope this helps.
Vince"
"SOLVED – APM 2.x - no power
I opened my APM control board and checked voltages after diode and found low value 1.49v
So I jumpered the diode with a small yellow wire.
Now powers up fine.
So I guess I fried the diode by applying the buzzer on the…"
I opened my APM control board and checked voltages after diode and found low value 1.49v
So I jumpered the diode with a small yellow wire.
Now powers up fine.
So I guess I fried the diode by applying the buzzer on the…"
"Addendum:
I measured voltages on APM with power module power and ESC power on output rail -
Output rail 5.5v
Input rail 1.1v
Acessory rail 1.1v
Thanks,
Vince"
I measured voltages on APM with power module power and ESC power on output rail -
Output rail 5.5v
Input rail 1.1v
Acessory rail 1.1v
Thanks,
Vince"
"SOLVED - I replaced my EMAX BLHeli 20amp ESC with Turnigy Basic 18amp just for a test and everything works fine now.
I guess I need to buy some REAL ESCs that are compatable with my PIX.
I will go shopping at HobbyKing.
Vince"
I guess I need to buy some REAL ESCs that are compatable with my PIX.
I will go shopping at HobbyKing.
Vince"
"Problem – Pixhawk not initialize ESC
07/04/16
Problem – Pixhawk not initialize ESCMy Pixhawk (firmware 3.3.3) controller will not initialize the ESCs on my home made QUAD.
I setup the Pixhawk origallialy on a HobbyKing Turnigy SK450 Quad with…"
07/04/16
Problem – Pixhawk not initialize ESCMy Pixhawk (firmware 3.3.3) controller will not initialize the ESCs on my home made QUAD.
I setup the Pixhawk origallialy on a HobbyKing Turnigy SK450 Quad with…"
07/04/16Problem – Pixhawk not initialize ESCMy Pixhawk (firmware 3.3.3) controller will not initialize the ESCs on my home made QUAD.I setup the Pixhawk origallialy on a HobbyKing Turnigy SK450 Quad with Multistar 20amp sbec and Multistar 2213 –…
