Gender
Male
About
Location
Beijing
About Me:
Benewake (Beijing) Co., Ltd. founded in Beijing, China in 2015. We are a technology company focused on autonomous driving, V2X, rail transit, civil aviation, shipping and industrial applications. By combining cutting-edged technology of LiDAR and efficient solutions, we empower our customers to transform their industries and markets, helping them to achieve safe and intelligent driving and bringing automation into systems for billions of people. Up to now, Benewake has applied for hundreds of patents and has more than 200 employees. We have a full range of business activities in China and abroad, including R&D, manufacturing, sales and services.
We built partnerships with the top 500 enterprises in China and abroad. Our business covers more than 100 countries and regions around the world, and the products are exported to Europe, America, Asia Pacific and other regions.
Please tell us a bit about your UAV interest
altitude hold and landing aid
Hometown:
China
Activity Feed
At the WAIC 2026 expo, nearly every embodied AI robot demonstrating real-world tasks was enclosed within a protective barrier. Safety personnel kept their eyes glued to the same vulnerable spots: feet, flanks, and arm trajectories.These three areas…
In 2022, a smart pool-cleaning robot project was quietly launched on Kickstarter. Back then, no one called smart pool robotics an "industry sector"—it was just a niche, forgotten branch within consumer robotics.Four years later, in 2026, this…
When integrating the TF03 LiDAR into your system, correct wiring is critical. A simple mistake—such as swapping power lines or misconnecting communication pins—can lead to communication failure or even permanent device damage.This guide walks you…
TFmini-Plus can directly be connected with the one of the serial ports of CUAV V5. There are four serial ports which can be used to interface LiDAR. The following port mapping shows hardware (left) and software (right) serial port mapping: TELEM1 >…
TFmini-Plus can be connected with the IIC port of CUAV V5. There are four IIC ports available on the flight controller, but by default, data can only be read through IIC port-2. In order to use other ports, some settings will be required like…
The configuring procedure is applicable to Cube Orange and Cube Black flight controllers. The interfaces available that can be used to connect TF03 are the same on both flight controllers.TF03-100, TF03-180 and TF350 can be interfaced with the one…
TFmini-Plus can directly be connected with one of the serial ports of Pixhawk 6C or 6X from Holybro. There are four serial ports which can be used to interface LiDAR. The following port mapping shows hardware (left) and software (right) serial port…
TFS20-L can directly be connected with one of the serial ports of Pixhawk 6C or 6X from Holybro. There are four serial ports which can be used to interface LiDAR. The following port mapping shows hardware (left) and software (right) serial port…
PX4 has its own unique advantages; it is preferred and liked by the majority of users. The TF series is a highly cost-effective LiDAR launched by Benewake, which is sought after by the majority of drone users. This tutorial introduces the connection…
Benewake TF Series (mini-S, mini-Plus, 02-Pro, Luna) LiDAR can be connected with the IIC port of PixHawk 6C and 6X Flight from HolyBro. There are three IIC ports available on PixHawk 6C:On GPS-1> pin-4: SCL1, pin-5: SDA1;On GPS-2> pin-4: SCL2,…
TFmini-S can directly be connected with the serial port of PixHawk. TFmini-S can be used in flight controller for the purpose of altitude holding or obstacle avoidance. This document is suitable to PixHawk adopts ArduCopter V3.6.2 or higher…
TFmini-S can be used with PixHawk for the purpose of obstacle avoidance.TFmini-SSettings:Note: Frame rate should be set to 250Hz, see the details in chapter 7.4 “frame rate” and changing the communication interface.The default communication of…
TFmini-i and TF02-i can be interfaced with PixHawk1 CAN port or any flight controller which has Ardupilot firmware flashed and having CAN interface. Support for CAN protocol has been added to Ardupilot firmwares, starting from Copter 4.2.0…
