Hello,
i want connect at least 4 Potis at Ardupilot Breadboard (i have only the red Board) and send its values via USB to PC.
USB-Transmit works in steps of 1,5 sec but i think there has to be a special command to define IN1 ... IN8 as ADC-Input.
Can an
Read more…Hallo,
I use 1.1.73 and AC 2.5.4
If I check Tune CH6_Loiter_P the Loiter P don´t change, it Changes the Loiter speed.
In what unit is Loiter speed? m/s?
And is Loiter P with 2.0 default normal before it was 0.5... or so and now Loiter P is 2.0 and Loiter
Read more…Hallo,
is it posible to make a Button for clearing the eprom manually?
thx
druckgott
Read more…Hallo,
today I have used the MP and tune Travelspeed.
I set value min to 0 and max to 6.0
Then I change the value via ch7 and read the params again.
if i´m on 0 it´s 0 if I put it put to 100% it´s not 6 it´s 60.
So I think this is a bug??!!
See picture
I te
Read more…Hi I have a sparkfun Mag:HMC5843
in this version it works perfekt:ArduCopter 2.2b4
in the newest version it don´t work 2.5.3
is this no longer supportet?
thx
druckgott
Read more…Hallo, I have mounted on my Quadcopter with AMP1 a sparkfun magentometer.
with all Version in 2.0* the copter is showing right in MP on the map who it stands in realaty for example to North.
Since I update to 2.1* and now to 2.2* the copter stand 180 d
Read more…Hallo, I have updatet the MP since a long time and see to my happynes there is a field to change CH7 Option.
But If I click on this I only have 4 Points and the rest is empty??
Is this a bug??
thx
druckgott
Read more…In 1.0.92 the radio configuration works perfekt.
On 93 some chanels don´t work and some are only 50%
that could this cause.
thx
druckgott
Read more…Hallo, I have arducopter 2.0.49 on my Quad + Copter.
Today I made aflight and only get a 2D fix.
But in the log I see I have 9 Sat´s.
What is the differenz between 2D and 3D fix and what can couse this?
thx
druckgott
Read more…Hallo, I have Simple mode over CH7 this works very finde.
The only think which do not work is to reset the "coordinate system".
I have to switch off the Copter and switch it on to get a reset for simple mode.
If I only switch it off an on it will not r
Read more…Hi,
what happens at the moment, if the reciver is going totaly off??
Normaly all values go to the middle?? Im´right.
So if the copter klimbe with the middle value you can get lost it and it´s also a safty thing???
Is it posible to set a failsave like
Read more…Hallo, if I set this on uploading the skech to my board and I switch the values in MP there stands always stabelised it do not switch to simple. If I switch via CH5 it works (the normal mode set)
is this normal?
Read more…Hi, is there a posiblity to tune the Loiter PID over chanel 6???
thx
druckgott
Read more…Hi,
my copter files now very well, but in Acro mode which is my favorit mode its more agillity like in stable, the copter always want to turn around yaw, if I do nothing on the yaw stick, the copter spinning around it self the whole time, but very sl
Read more…Hallo, which PID´s do I have to change to get a better Acro Mode.
Because at the moment my Copter is in Acromode very tipsy and it´s hard to fly, but I love this mode mor then the stab. Mode.
I also fly Acro mode on Multiwii, thats better to fly as st
Read more…Hallo, I read this blog:
Now I have buy this adapter.
I have created a hex file from the spektrum_to_ppm_encoder and upload it to the 328p chip.
I a
Read more…Hallo, today I want to upload the new firmware for aducopter .41
after the compilation I get an error:
avrdude: stk500_getsync(): not in sync: resp=0x00
I read several Posts in this forum, and in the wiki to solve this problem. I have testet it on more
Read more…Hallo,
it will be nice if it´s selectabel which for example arducopter Version you will be upload to the copter.
So that you can select older versions and the aktuell version will be preselectet, but sometimes the new version works not so good like an
Read more…Hallo could MO the developer check this:
http://diydrones.ning.com/forum/topics/mag-crashed-hmc5843
Could this a bug in the MP???
Copter Version 2.0.39 and MP 54
thx
duckgott
Read more…Hallo, since 2 days I have a problem with my Magnetometer HMC5843 I have tested it with the testcode for the compass.
The initalistation faild:
It fails on this codeline (AP_Compass_HMC5843.cpp)
if( abs(mag_x) > 500 && abs(mag_x) < 2000 && abs(mag_y) >
Read more…