About

Gender

Male


Location

Westland, MI


About Me:

i am a CO2 laser tech


Please tell us a bit about your UAV interest

just starting out


Hometown:

livonia michigan


Activity Feed

glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"to bad someone cant make up a sort of cover. if i know solid works i would try."
Nov 29, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"Well i did a complete reset of my APM 2.5... and that did fix it. i will get some pictures up on here. thanks for all your help Brendan, and a great Quad..."
Oct 28, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"ya i am going to try this APM in my 3dr X frame and see what happens.... But thanks for all your help. you did help a lot."
Oct 27, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"ya in the radio calibration screen the throttle does not kick in till i get to 1544. the stick reading is 1124 and stick all up is 1912. and this is on a APM 2.5 with the qbrain."
Oct 27, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"no what i was saying was if i do a all at once  calibration, it works. and then move the stick up and the motor spin. bet then after i power down the quad. power back up, that is when i have to be above 50%. Hmm but i am looking. Oh firmware is 3.15"
Oct 26, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"ya i did follow the all at once. but i will try with it plug into channel 1. i know my 3dr frame with APM 1.0 is different but i cam spin the motors at slow speed. Oh i just did a re-calibration and after calibration i can move the stick up and the…"
Oct 26, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"well i did get it to work, but now the problem is the motors will not spin till the stick is at 50% power. then they spin... is their any setup in the qbrain i have to change?"
Oct 26, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"has anyone here used the QBRAIN WITH THE APM 2.5? if so how do you wire the output to the esc. i see a small jumper j1 should this be in out out?"
Oct 25, 2014
glenn nafin replied to Brendan22's discussion 3D printed T4 and T6
"how are you guys calibrate the qbrain? do it with the APM? or use that hub they sent with it?"
Oct 25, 2014
glenn nafin replied to Andreas M. Antonopoulos's discussion ArduCopter 2.7.1 Released
"ok, i know it was ask before, But.. do i have to erase the eprom before i load this? right now i have 2.7 on my quad..."
Aug 5, 2012
glenn nafin posted a discussion
apm1 3dr running in X. well i was flying it and i landed hard, went to refly it and now my controld are reverse.... i push stick right it banks left, i pull back it goes forward....Hmmm anyone seen this before?
Apr 7, 2012
glenn nafin posted a discussion
when we update the firmware should we erase the eprom and reconfig it all over.... or just load the new FW and go fly...
Mar 25, 2012
glenn nafin posted a discussion
i was looking for some props at my local hobby shop and all they had were 12x3.8.... and i see on the order form when you pick what prop you want the 12 is 12x4.5...... think the 3.8 will work? i have the 880 motors in the 3d frame...
Mar 17, 2012
glenn nafin replied to Randy's discussion ArduCopter 2.4 released
"how do you pick what to use for alt hold? sonar or  baro??"
Mar 16, 2012
glenn nafin commented on Luke's blog post How to Program 6 Flight Modes for ArdupilotMega - JR 9303 Example
"wow, this setup work great... thanks...."
Mar 14, 2012
glenn nafin posted a discussion
Hi my VSI gage is jumping aroung with the quad just sitting on the ground....am i missing something here? here is a vid..... and i have the latest FW on it.. Oh i do have a sonar on it but its the ez4...could this be it?VSI.3gp
Mar 13, 2012
More…