About

Gender

Male


About Me:

Security intergrator


Please tell us a bit about your UAV interest

Want to start off with apm 2.5 in a raidian pro airplane airspeed sensor, gps, telmetry and add fpv as funds become available


Hometown:

louisville


Activity Feed

kevin commented on PX4's blog post PX4 and 3D Robotics present Pixhawk: An Advanced, User-Friendly Autopilot
"Will my card be charged right away, or not until it ships?"
Sep 2, 2013
kevin commented on PX4's blog post PX4 and 3D Robotics present Pixhawk: An Advanced, User-Friendly Autopilot
"So are we hinting at Apm 2.6 may be the last Apm? ie no Apm 2.7 or Apm3. The Pixhawk is the Future of 3DR and DIY? Cause I like it! Pre-order time!!!"
Sep 2, 2013
kevin posted a discussion in ArduCopter User Group
I'm currently searching for the right AP equipment.  I'm currently using a gopro 2 but will soon be getting a hero 3.  I using 6 of the available 7 ch on my receiver.  I would like to hear from the diydrone community on what u use or what new…
Aug 12, 2013
kevin replied to kevin's discussion GSC Compass shows 180degree change for a 90degree turn? in ArduCopter User Group
"ANYONE? "
Aug 10, 2013
kevin posted a discussion in ArduCopter User Group
I did the live compass mot test several times and keep getting 17 17 17 and it tells me its saved the changes but it starts out 180 degree out of phase, meaning red gps heading line point out the back instead of foward. So in a nut shell, out of the…
Aug 6, 2013
kevin replied to kevin's discussion Dli F550 + APM 2.5 + PM + DX7/AR7000 Build Questions in ArduCopter User Group
"I had my Maiden Flight today!  1st try to lift off, it started lifting to one side.  I lowered the throttle a bit, raised it again and lift off!!!  Put it back down again quickly.  All my controls were backwards. So I disarmed my hex, changed my…"
Aug 4, 2013
kevin replied to kevin's discussion Dli F550 + APM 2.5 + PM + DX7/AR7000 Build Questions in ArduCopter User Group
"Also, is it better to mount Apm inside the frame or on top?"
Aug 2, 2013
kevin posted a discussion in ArduCopter User Group
My first question is....the BEC? Do I need it?  I'm pretty sure I do.  Where does it go? I'm thinking I saw something about a stock DJI F550 frame, esc, motor, must use an esc. I have a Turnigy SBEC 8-40V max 5A. switchable 5 or 6 volts.  Should…
Aug 2, 2013
kevin replied to kevin's discussion Day 2, What went wrong? in ArduPlane User Group
"this is the last flight that day. CG was perfect! Ignore the last flight log pls. And thank you very much for taking time to help me as I am confused as to what happened over night? I didn't change any settings to anything. I also included my log…"
May 10, 2013
kevin replied to kevin's discussion Day 2, What went wrong? in ArduPlane User Group
"in stab plane pitches down between 15 and 30 degrees nose down but flew perfect the day before.  plane shows level on HUD when its level on ground and control surfaces react correctly in stab on ground."
May 9, 2013
kevin posted a discussion in ArduPlane User Group
Maiden flight yesterday went great.  So today I tried without my Gopro under the wing and outta 4 flights... All was not right.  So after takeoff I switched into Stab and the plane nosed in and although wings were level, the pitch was always nose…
May 8, 2013
kevin posted a discussion in ArduPlane User Group
Absolutely Amazing!  Started off in manual mode, switched to stab about 30 sec after takeoff and even heavy and most probally heavier on one wing due to gopro2 under wing it preformed perfect!  Changed to FBWB and again, perfect. Landed, setup some…
May 7, 2013
kevin posted a discussion in ArduPlane User Group
I was looking at the RVJET.  Looks like it can be broken down for transport fairly easy and has lots of room for equip.  What airplane do you like, use, want to outfit?http://diydrones.com/profiles/blogs/range-video-s-fpv-flying-wing-t...
May 5, 2013
kevin posted a discussion in ArduPlane User Group
My DX7 transmitter is using aux 2 for my 2nd Ale and my gear channel is activating APM mode switching (2 pos, high-low) and my 3 pos sw isn't doing anything! Although this will work and I should be close to my maiden flight, I would like to have…
May 1, 2013
kevin left a comment for John Zaner
"Louisville, Ky"
Apr 29, 2013
kevin replied to kevin's discussion Need Advise PLS!!!! in ArduPlane User Group
"I could use some help on TX/mode switching with the DX7 and my set up. I have things mostly setup correct but need a lil tweaking help with my Radian pro.  Any chance anyone with a good understanding of the DX7 as it applies to this airframe and APM…"
Apr 29, 2013
More…