About

Location

karachi


About Me:

student


Please tell us a bit about your UAV interest

to fly a quadcopter


Hometown:

karachi


Activity Feed

saba posted a discussion in ArduCopter User Group
I am designing a HexaCopter with 1000mm Motor to Motor length.My aluminium frame is almost ready, my required / proposed flight time is 30 minutes and payload is 2 ~ 2.5 Kg.What electronics should i use??LiPo BLDC ESC Autopilot Propllers Etc ..Any…
Dec 26, 2013
saba replied to Paul Bizard's discussion Matlab/Simulink Simulator
"dear sir
great work. any reference material for aerodynamic equations and stability coefficient used in this simulation. 
regards
saba"
Aug 28, 2013
saba left a comment on ArduRover User Group
"Dear TJC
Thanks a lot. it was my receiver connection problem. thanks to resolve.
regards
saba"
Apr 8, 2013
saba left a comment on ArduRover User Group
"Dear TJC
i am sorry. my JP1 is not connected. no issue of output power. only the output pin 2 (Forward/Reverse) has problem. because if i connect output pin 1( steering) to Forward/Reverse Motor of vehicle, it works fine. so pl highlight the part of…"
Apr 5, 2013
saba left a comment on ArduRover User Group
"dear TJC
My J1 is connected and power of servo is from a battery of 5v and receiver is getting power from APM 2.5. APM 2.5 is getting power from laptop USB port.no ESC is here. i am using Mission Planner. What is PM in your reply.
regards
saba "
Apr 3, 2013
saba left a comment on ArduRover User Group
"daer all
my Forward/ Reverse output channel is not continuous. i have to reconnect power(USB) when it stuck. My firmware is ArduRover_v230_firmware_20130321ss2. I have performed all CLI, Radio reset.
regards
saba"
Apr 2, 2013
saba left a comment on ArduRover User Group
"thanks thomas. i really appreciate your help for this forum.
best regards
saba"
Mar 29, 2013
saba left a comment on ArduRover User Group
"pl advise about the vehicle
http://traxxas.com/products/models/electric/3605stampede
my interface b/w ardupilot and DC motor(steering mechanism)  is not accurate. that's why i am searching the exact compatable vehicle??
thanks
saba
 "
Mar 29, 2013
saba left a comment on ArduRover User Group
"dear all
i am using the firmware ArduRover_v230_firmware_20130315SS1. output channel1 is steering servo and output channel2 is forward/reverse. in output channel 2 (forward/reverse) if i attach servo motor and check it by giving input from…"
Mar 26, 2013
saba left a comment on ArduRover User Group
"thanks Thomas
this discussion have informative links. pl clear me about the firmware. i need 2 output channel (1 & 3 as defined in ardurover google group document). in my setup channel1 output is there but at channel 3, no output. my firmware is…"
Mar 14, 2013
saba left a comment on ArduRover User Group
"dear all
in my vehicle i have dc motors for forward/reverse and left/right. my apm output is PWM. so how to convert PWM to voltage.
thanks "
Mar 13, 2013
saba left a comment on ArduRover User Group
"thanks TCIII
Follow your instructions for CLI settings. some observations
my steering servos are moving on channel1 output with right left of transmitter channel. but output channel 3 is not giving any output at osilloscope. ???
second the vehicle…"
Mar 12, 2013
saba left a comment on ArduRover User Group
"thanks TCIII
i am using the latest software i.e
ArduRover_v230_firmware_20120222 & Mission Planner 1.2.33. i followed your instructions to configure. pl clear me that during this should the link connected or not. b/c in this …"
Mar 8, 2013
saba left a comment on ArduRover User Group
"dear all
i have a ground vehicle (jeep) named TORQUE HORSE. it has the feature of Forward/Reverse, Right/Left. pl see the below link
http://detail.en.china.cn/provide/1002172928.html
i have downloaded the latest alpha software on my ardino board.…"
Mar 7, 2013
saba left a comment on ArduRover User Group
"dear all
thanks to everyone in the forum. finally compiled the latest code. but i achieve this by coping all the Library files of firmware in the library of ardino software. i think that this may help others who are facing compilation problem. now i…"
Feb 28, 2013
saba left a comment on ArduRover User Group
"i tried these options but still getting error. pl see the attachment. i searched a lot on forum. my computer is 64bit. pl....see this attached error."
Feb 27, 2013
More…