About

Gender

Male


Location

seoul


About Me:

i am a newbie and i want to run many things through this site


Please tell us a bit about your UAV interest

i bought APM 2.6, pixhawk and telemetry through 3DR Robotics and am trying to make UAV by myself.


Hometown:

seoul


Activity Feed

sijongmu posted a discussion
hi everyone!referring other's guidance, i organized FPV function by aligning following parts.APM 2.6Sony Double Scan 960H CCD Effio-V 800TVL WDR Cameraimmersionrc 5.8ghz txfoxtech explorer monitor & 5.8ghz diversity rxminimosdbut when i supplied the…
Dec 9, 2015
sijongmu replied to Karan Chawla's discussion Realistic Constraints for a Delivery Drone
"hi Karan!

i also have been thought the same concept of you. in my opinion, if you set the category of 2kg payload and 13km range,
there is no differences with normal Hexacopter which can lift 3-4kg additionally. so i recommend you to consider
some…"
Nov 22, 2015
sijongmu posted a discussion in PIXHAWK
hi! everyone!i read in this site, to connect the pixhawk with 6s battery, many people usually use atto pilotpower module. but someone informed that the Crius power module was good without further solderingwork.so i bought it and connected it with…
Oct 4, 2015
sijongmu posted a discussion
hi everyone!now i am confused and a bit frustrated, would appreciate any help as i'm not sure howto proceed set up the direction of pixhawk and mission planner's gauge.recently i finished to insert the factor of pixhawk's full parameter through…
Sep 19, 2015
sijongmu replied to Damo's discussion Finwing penguin takeoff issues in ArduPlane User Group
"hi moglos!
 
i bought pixhawk and now i am hesitating how can i set the FBWA mode to my plane.
would you advise me the method or procedure for me?
 
rgds
 "
Aug 15, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"hi Richard!
you are really my good teacher^^. i don't know the electricity and role of each pin
so much. pls advise your good knowledge of GND theory without hesitate^^.
 
re APM case, i understood well and i will make the holes to connect to the…"
May 27, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"hi Richard!
as per your guide, i opened the case of apm 2.6(it was not easy^^) and i found the UART2 point accordingly. flwg point is right?
























then what is the next step?

as i understood, it needs some soldering to connect the…"
May 26, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"hi richard!

thanks for your explanation. the different things between you and me is the router and level shifter.

first, i also connected APM-RPI2-4G router. i used 4G router but it's almost same string with you.
so already i commented above to…"
May 25, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"hi Efstratios!
 
yes i reviewed your capture of cable but i doubt why this cable can't connect in order.


as you like, i am a newbie in this field so i don't know where can i buy the same usb connector like yours. or i guess i should cut other usb…"
May 25, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"thanks Efstratios!

i will review your check point again.
also i have one question that cable usb to serail means flwg port cable?
as i know, usually the cable is connected between apm or pixhawk to raspberry pi or Odroid.
then above cable can't be…"
May 23, 2015
sijongmu replied to sijongmu's discussion connect telemetry through TCP & UDP in Volta Robots
"hi Efstratios!

Really thanks for your advice^^. i think you also had experienced so many trial and errors like me^^.
yes i have a pixhawk but now i am using APM 2.6, raspberry pi 2 and mission planner and
my devices was sett up as like your…"
May 21, 2015
sijongmu posted a discussion in Volta Robots
hi Silvio!i have tried 4G telemetry as like you but i have failed continously to connectthe mission planner with 4G network.attached pls find the screen capture of my trial.when i push the connect button under the condition of TCP, it showed "host…
May 21, 2015
sijongmu commented on LightWare - Laser Developer's blog post Obstacle detection LRF takes 36000 readings per second and costs only US$350
"@LD
thanks for your reply!
i hope i can review your product asap!

rgds CS"
Mar 23, 2015
sijongmu commented on LightWare - Laser Developer's blog post Obstacle detection LRF takes 36000 readings per second and costs only US$350
"Hi LD!
i have been interested in your good product continously. but i can't find the demo film of SF/30B & 30C.
could you show me the film of performance in details?

rgds CS"
Mar 22, 2015