Alternate way of connecting compass...?

Hi all,I recently purchased and have finally put together my Arducopter from Jdrones.My compass came with wires and plug attached but I decided to unsolder these and attach directly to board as recommended, in doing so have bent two of the pins and possibly lifted two of the pads and broken the track on the APM board, I've traced one of the tracks (SDA) to a pin on one of the connectors and replaced with a tiny wire but the other broken track, the one (that goes to SDL on the compass)I cannot see where it goes to solder a replacement wire to it... I know this is all dodgy but don't want to hand over another $160 for a new board...The GND and V+ are fine.Thanks,Luke

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Do not use the pin !, solder soft wire directly to the track on the apm and mag ( shielded is preferred, like usb) and mount the compass in a plase with non noise from other electronic
This reply was deleted.

Activity

DIY Robocars via Twitter
Sep 9
DIY Robocars via Twitter
RT @chr1sa: We've got another virtual @DIYRobocars race tomorrow at 9:00am PT. Two dozen autonomous cars will compete, four at a time. Ther…
Sep 4
DIY Robocars via Twitter
Sep 1
DIY Robocars via Twitter
Aug 31
DIY Robocars via Twitter
Aug 31
DIY Robocars via Twitter
RT @ExplorerRobocar: Sometimes, I am really a big kid!! Having fun with my virtual RC car on the @diyrobocars track 😜😉, by using the « AR R…
Aug 24
DIY Robocars via Twitter
RT @grepLeigh: @donkey_car @unity3d @TensorFlow ~1050 episodes into training, my agent learned to erratically drive in the left lane. 🤖😆 ht…
Aug 24
DIY Robocars via Twitter
RT @EclipseCyclone: Sweet! http://Robotec.ai high performance #ROS 2 @unity3d #CycloneDDS bridge for @AutowareFdn @SVLSimulator now…
Aug 24
DIY Robocars via Twitter
RT @a1k0n: My car had a lot of trouble getting around the track at the last @diyrobocars event -- only one actual finished lap during the r…
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map https://t.co/VzykOkUt2G
Aug 24
DIY Robocars via Twitter
RT @SmallpixelCar: Made a lot progress on Warm Spring Raceways track. Almost finished one lap. https://t.co/nUVpufZQyP
Aug 24
DIY Robocars via Twitter
RT @AntonioRobotics: Super fun time seeing these autonomous cars race at @circuitlaunch for the @diyrobocars quarterly meet up! The demolit…
Aug 15
DIY Robocars via Twitter
RT @a1k0n: I thought my dumb localization code was still working at the new @circuitlaunch track, but it was just *barely* working. I shoul…
Aug 14
DIY Robocars via Twitter
RT @DAVGtech: Recording of entire in person @diyrobocars race today @circuitlaunch. Fast forward a couple hours to go straight to the racin…
Aug 14
DIY Robocars via Twitter
RT @SmallpixelCar: This is the run time map. Very noisy Lidar signal https://t.co/bAbeVUMi10
Aug 14
DIY Robocars via Twitter
RT @SmallpixelCar: Today’s race with @a1k0n at @diyrobocars We both decided jumping over the wall was the way to break the 11s lap time. Th…
Aug 14
More…