APM 2.5 input port 1 problem

Hi forum

I've interchanged plus/minus connecting the Lipo.
The ESC and the power module had bin killed
and I've replaced them. The plane worked well
for the next two flights. But today the APM
is not showing any reaction to the input signal
on port 1. I've looked only at the mission
planner's radio calibration panel. The signal
is shown when connected to other ports but not
on Roll port. I've uploaded the firmware again
but no success.

Is it a deferred kill of the APM or what else can
I check?

thanks
Wolfgang R.

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • Strange, below the connector pin 1 was no longer connected to the line of the board.

    But better than to buy a new APM.

    Wolfgang R.

This reply was deleted.

Activity

DIY Robocars via Twitter
Videos from the ICRA autonomous racing workshop are now available: https://linklab-uva.github.io/icra-autonomous-racing/
Thursday
DIY Robocars via Twitter
RT @SmallpixelCar: Prepared race track for Warm Spring Raceways @wsraceways and looking forward to test my new car at RAMS RC @ramsaicar fa…
Jun 6
DIY Robocars via Twitter
RT @f1tenth: Trying out some nasty blocking maneuvers 🏎️🤖 #f1tenth #autonomousracing https://t.co/nMTstsaogM
Jun 5
DIY Robocars via Twitter
May 27
DIY Robocars via Twitter
RT @araffin2: I will talk this Saturday from 18:00 to 19:00 Paris time for the @diyrobocars community about learning to race in hours using…
May 27
DIY Robocars via Twitter
RT @a1k0n: Luckily the infeasible hairpin problem was easily reproducible in simulation and I could test the fix before bringing the car ba…
May 26
DIY Robocars via Twitter
RT @a1k0n: Another problem was that I was over-constraining the car's allowed accelerations, so it didn't think it could turn as tight as i…
May 26
DIY Robocars via Twitter
RT @a1k0n: Breaking the map up into two halves worked, but I had to be more careful about separating the inner track from outer. There's se…
May 26
DIY Robocars via Twitter
RT @a1k0n: Here's a datalog for my fastest lap of the day. Lap timer is tiny window lower-left. https://t.co/myrlWWrKUY
May 26
DIY Robocars via Twitter
May 26
DIY Robocars via Twitter
RT @a1k0n: Here was my car's POV. Man this track is confusing in first-person! After the incident my camera was all scuffed up and I was af…
May 23
DIY Robocars via Twitter
RT @circuitlaunch: Loved seeing so many familiar (masked) faces at Circuit Launch today for our first in person @diyrobocars in over a year…
May 22
DIY Robocars via Twitter
RT @circuitlaunch: Last but not least, mystery guest @BostonDynamics Spot took to the track @diyrobocars He enjoyed the #brazilianbbq too 😂…
May 22
DIY Robocars via Twitter
RT @SmallpixelCar: Today’s race @circuitlaunch for @diyrobocars with @a1k0n Was busy in the morning and did not get a chance to tune camera…
May 22
DIY Robocars via Twitter
RT @a1k0n: This was epic. My car was barely working this morning, had to make a lot of changes and extremely dirty hacks. Post-race analysi…
May 22
DIY Robocars via Twitter
DIY Robocars @ Circuit Launch, 3/7/2020 https://twitch.tv/diyrobocars
May 22
More…