Can someone look at my F450 quad build?

Hi All,

I'm finishing build of my first quad. Can someone take a minute to look what i did? Any advice will be greate about electronic placement etc. The ESC signal wires are temporary not in place just attached to spin up the motors. Reciver AR6210 with sattelite is in good place? Power module is my pain as i don't know where to put it, so is on the side of the quad for now... 

Also when i ARM the copter the motors not spin slowly by itself (i use newest firmware AC3.1.2) but when i push a throttle for a little up and go down the motors spin slowly and then one of them stop... Is that normal? I use Spectrum dx6i TX. please for any help...

Ps. I fly helicopters for 4 years (600 and 450) so not so noob in RC.

DSCN8938.JPG

DSCN8932.JPG

DSCN8934.JPG

DSCN8935.JPG

DSCN8937.JPG

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • have you calibrated your ECS, I had the similar problem until I re ran my esc configuration, also make sure that your rc transmitter is properly calibrated and settings are recorded before you do any motor/esc calibrations, if you make any changes to the remote control always redo the esc calibration, just what I had learned to do to avoid things like you are experiencing, it also might mean that your compass is no calibrated right so its doing some weird correcting with the motors to level it out, I am not sure, but the ESC is the more plausible scenario

This reply was deleted.

Activity

DIY Robocars via Twitter
Sunday
DIY Robocars via Twitter
Saturday
DIY Robocars via Twitter
Saturday
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
Saturday
DIY Robocars via Twitter
May 11
DIY Robocars via Twitter
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Noticed my car zigzagged in last run. It turned out to be the grass stuck in the wheel and made the odometry less accura…
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Test my car. RTK GPS worked great. Thanks @emlid for their support. https://t.co/EkQ6qmjmWR
May 8
DIY Drones via Twitter
RT @chr1sa: @kane That's @diydrones circa 2009. Still have a box of those Canon cameras that we used to strap into planes, just like this.…
May 3
DIY Robocars via Twitter
RT @chr1sa: Our next @diyrobocars race is going to be outside at a real RC racetrack in Fremont on May 28. Fully autonomous racing, head-to…
Apr 30
DIY Robocars via Twitter
RT @f1tenth: Our Spring 2022 F1TENTH course @PennEngineers is coming to an end with a head-to-head race as a big finale. So proud of our st…
Apr 26
DIY Robocars via Twitter
RT @DanielChiaJH: I wrote a thing! Throughout the development of my @diyrobocars car I've been using @foxglovedev Studio to visualize and d…
Apr 23
DIY Robocars via Twitter
RT @SmallpixelCar: My new car for high speed. Low body, everything ( @NVIDIAEmbedded Jetson Xavier NX, @emlid RTK GPS, IMC) under the deck…
Apr 23
DIY Robocars via Twitter
Apr 21
DIY Robocars via Twitter
RT @f1tenth: F1TENTH Race training setup @PennEngineers for our upcoming ICRA2022 @ieee_ras_icra competition. @OpenRoboticsOrg @IndyAChalle…
Apr 21
DIY Robocars via Twitter
RT @fatcatFABLAB: Proud to be hosting a restarted DIY Robocars NYC Meetup April 26. Come by if you want to talk about and race self-driving…
Apr 17
More…