Do ESCs get damaged after props hit the ground

Hi guys,
When an drone crashes and the propellors hit the ground do the ESCs get damaged. My drone crashed one while I was flying and motor 1 hit the ground along with the propellor. The motor was damaged so I replaced the motor checked and the esc1 seemed to be working fine(Motor 1 was rotating). The next time I flew it the drone climbed and after a while the esc1 failed and crashed (The drone flipped to that side and one FET was also burnt). Was the esc1 already damaged after my first crash?. While taking off it worked fine but did it burn when the load was too high.
Should we replace the esc when the props hit the ground and how do we check if the esc is working

Thank you in advance

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –

Replies

  • so you are considering seriusly repair that esc instead of pursache one new?

  • Depends of the sytem used by that particular esc..

    While the motor is spining, the impedance of the colis(wired in delta confiduration normally) is hig, because the magnet is moving to the center of the coil... is generated an extra back emf  ...

    but when the magnets dont move, or the same: the motor is not turning that extra back emf dont exist in the coils...

    so its only present the autoinduction factor, in consecuence the impedance is lower than the turning situation.

    so yes, is the motor is stoped more current is required and the transistors will dranin more current... but if the esc is good,

    it can avoid the burning od the transistor by having a dinamic limit...

    you can chek the state os your transistors with a amperimeter or an osciloscope comparing the esc outputs on a specific load

    maibe an esc manufacter will expalin this situation much better, anyone?

This reply was deleted.

Activity

DIY Robocars via Twitter
May 15
DIY Robocars via Twitter
May 14
DIY Robocars via Twitter
May 13
DIY Robocars via Twitter
RT @f1tenth: Say hi to our newest #F1TENTH creation for @ieee_ras_icra next week in Philly. It’s going to be huge! 😎 🔥 @AutowareFdn @PennEn…
May 13
DIY Robocars via Twitter
May 11
DIY Robocars via Twitter
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Noticed my car zigzagged in last run. It turned out to be the grass stuck in the wheel and made the odometry less accura…
May 8
DIY Robocars via Twitter
RT @SmallpixelCar: Test my car. RTK GPS worked great. Thanks @emlid for their support. https://t.co/EkQ6qmjmWR
May 8
DIY Drones via Twitter
RT @chr1sa: @kane That's @diydrones circa 2009. Still have a box of those Canon cameras that we used to strap into planes, just like this.…
May 3
DIY Robocars via Twitter
RT @chr1sa: Our next @diyrobocars race is going to be outside at a real RC racetrack in Fremont on May 28. Fully autonomous racing, head-to…
Apr 30
DIY Robocars via Twitter
RT @f1tenth: Our Spring 2022 F1TENTH course @PennEngineers is coming to an end with a head-to-head race as a big finale. So proud of our st…
Apr 26
DIY Robocars via Twitter
RT @DanielChiaJH: I wrote a thing! Throughout the development of my @diyrobocars car I've been using @foxglovedev Studio to visualize and d…
Apr 23
DIY Robocars via Twitter
RT @SmallpixelCar: My new car for high speed. Low body, everything ( @NVIDIAEmbedded Jetson Xavier NX, @emlid RTK GPS, IMC) under the deck…
Apr 23
DIY Robocars via Twitter
Apr 21
DIY Robocars via Twitter
RT @f1tenth: F1TENTH Race training setup @PennEngineers for our upcoming ICRA2022 @ieee_ras_icra competition. @OpenRoboticsOrg @IndyAChalle…
Apr 21
DIY Robocars via Twitter
RT @fatcatFABLAB: Proud to be hosting a restarted DIY Robocars NYC Meetup April 26. Come by if you want to talk about and race self-driving…
Apr 17
More…