Pixhawk weird behaviour

I bought Radiolink Pixhawk a few days ago. Loaded it with APM plane 3.9 and mounted it on my flying wing. Did all bench test like stabilizing, failsafe trigger and power module tuning. All worked well and i also did a test flying. During first flight it behaved normal, i tested stabilize mode and it was stabilizing the wings but with nose down posture so i thought i need to do acclerometer calibration again by keeping nose a bit up so that it can maintain level flight. I also connected mavlink to TBS diversity receiver and i was getting flight data from pixhawk to ground TBS crossfire tx module on Tower app on my android through bluetooth.

Now next day i did calibration and my buddy launched the craft just after takeoff motor shut down and i had no control from transmitter. I did another launch same thing happened again. As my buddy launch the wing within 1sec it cuts the throttle and the rc control. 

So i reinstalled the firmware and did all mandatory stuff. Then i tested it on bench. I found that after arming as i increase throttle more than 50% it cut the radio signals and after 3 sec it cuts the throttle. Pixhawk reboots  it self. At first i thought it can be a faulty power module. So i changed it with my old trusted one. Then tested in workshop( bench test) there it worked fine it was not cutting the signals and i had control over power.

Next day at flying field i took off and did some circuiting checked stabilize, it behaved weird so back to manual. After 1 min. for flying i suddenly lost the radio signal and craft crashed it the ground with resumed throttle. There is no problem with radio, it works very well because i've tested it over 15 miles.

i can't figure out what is wrong with it. 

Following stuff i used-

Radiolink pixhawk with M8N Gps

TBS Crossfire radio system with diversity receiver providing PPM out.

Turnigy 9xr Pro

You need to be a member of diydrones to add comments!

Join diydrones

Email me when people reply –
This reply was deleted.

Activity

DIY Robocars via Twitter
RT @chr1sa: Our next @DIYRobocars virtual AI car race is next Saturday. Compete from home using the @donkey_car simulator -- no physical ca…
10 hours ago
DIY Robocars via Twitter
RT @RoboticMasters: Students from @Sydney_Uni working hard on improvements and changes to @donkey_car simulator. @diyrobocars @adafruit…
10 hours ago
DIY Robocars via Twitter
Practice virtual race this Saturday; the real thing will be on Oct 3 https://www.meetup.com/DIYRobocars/
Wednesday
DIY Robocars via Twitter
Wednesday
Derrick Davies liked lisa TDrones's profile
Wednesday
DIY Robocars via Twitter
Sep 21
DIY Robocars via Twitter
RT @SahikaGenc: AWS DeepRacer & Hot Wheels Track https://youtu.be/4H0Ei07RdR4 via @YouTube
Sep 14
DIY Robocars via Twitter
Sep 8
DIY Robocars via Twitter
RT @davsca1: We are releasing the code of our Fisher Information Field, the first dedicated map for perception-aware planning that is >10x…
Sep 8
DIY Robocars via Twitter
RT @SmallpixelCar: How this works: 1)object detection to find cones in single camera image, 30 frames/sec on @NVIDIAEmbedded Xavier. 2)comp…
Sep 8
DIY Robocars via Twitter
RT @SmallpixelCar: Use two color cones to guide the robocar. No map needed, on onsite training needed. Just place the cones and it will fol…
Sep 7
DIY Robocars via Twitter
Sep 7
DIY Robocars via Twitter
RT @roboton_io: Great to see http://roboton.io running at 60fps on the cheapest #chromebook we could find! #edtech #robotics #educat…
Sep 3
DIY Robocars via Twitter
RT @openmvcam: Crazy in-depth article about using the OpenMV Cam for Astrophotography: https://github.com/frank26080115/OpemMV-Astrophotography-Gear https://t.co/BPoK9QDEwS
Sep 3
DIY Robocars via Twitter
RT @openmvcam: Hi folks, it's finally here! Our first draft of our Arduino Interface Library is out! It works over SoftwareSerial, Hardware…
Sep 3
DIY Robocars via Twitter
RT @chr1sa: Please let them have an open API. This would be perfect for @DIYRobocars races https://twitter.com/NintendoAmerica/status/1301513099707658246
Sep 3
More…